Janome Crafts & Hobbies - Popular Questions, Answers, Tips & Manuals


HI, this sometimes happens when it needs cleaning. Sometimes lint and thread gets caught underneath the sewing plate, so try giving it a thorough clean. Hope it helps.

Janome MyLock... | 290 views | 1 helpful votes


Hi Selma, The links below are a FREE 42 page Instruction book and a youtube video showing a janome overlocking tutorial, Also there's videos down the right side of that link that may help as well........... CHEERE..
http://janome.com/siteassets/support/manuals/sergers/inst-book-7034d-english.pdf

Janome Domestic Overlocking Machine Tutorial

Janome MyLock... | 689 views | 0 helpful votes


Try searching the internet for:

Make + Model + the word "Manual"

or contact manufacturer support or a dealer.

...

Janome MyLock... | 493 views | 0 helpful votes


sounds like you could have a short in the machine, if it keeps happening you should have the machine checked

Janome 8077... | 569 views | 0 helpful votes


sounds like a computer problem, the machine needs to be serviced

Janome Memory... | 605 views | 0 helpful votes


It might be best to contact Janome Support or call a Janome dealer. There is probably a way to reset your machine, but that information doesn't seem to be readily available on the internet.

http://janome.com/en/support

...

Janome Memory... | 505 views | 1 helpful votes


the feed dogs could be broken or the lever that raises the feed dog could be broken, needs to be serviced

Janome HD3000... | 631 views | 0 helpful votes


contact Janome thru their website and ask tech support what might be problem .

Janome Memory... | 801 views | 0 helpful votes


the machine needs to be serviced, could be a computer problem

Janome Hello... | 716 views | 0 helpful votes


put them on your computer first,then after you know you have them,copy them

Janome Memory... | 631 views | 0 helpful votes


here is a link to click on for Janome customer service and ask them about the error

http://janome.com/en/contact-us

Janome 8077... | 779 views | 0 helpful votes


Check you instruction manual. The Bobbin goes in under the pressor foot. You need to lift or pop out the clear cover. Unsure if it is clockwise or anti-clockwise insertion. Book will tell

Janome Memory... | 308 views | 0 helpful votes


the bobbin winder spindle probably needs to be checked to see if there is a part broken or if it needs some type of adjustment

Janome HD3000... | 460 views | 0 helpful votes


Caring for and cleaning a sewing machine is much the same no matter what model/make, I can't actually see a manual for yours but in general terms this is what I do.

Keep it covered and out of direct sunlight when not in use, sunlight is tough on plastic shell cased machines. Also unplug the power lead when not using, just in case of electrical fusion.

Each time you use your machine do the following (I do it when I start a new project, then clean before putting away in the cupboard if I'm not going to be back to it for a while):
wipe external surfaces to remove any thread dye particles, lint or dust. Unplug, then lift presser foot and unscrew the metal cover plate and remove to expose the bobbin case. Remove the bobbin and then lift out the bobbin holder. (With my Janome, this is held in by a magnet and there are two markings that line up to realign the case). Brush out all lint that you can get to or use tweezers to remove, you don't want to blow it further into the machine so never use canned or compressed air. Clean the bobbin holder too. With mine, there is a little wick for lubrication in the middle of the race, add a drop of good quality clear sewing machine oil, then replace the bobbin holder and cover plate.
25337008-k4hvezj240pt3jcsmcbnor2m-1-0.jpg
Clean the tension discs, to do this raise the presser foot, then "floss" between the tension discs (that dial on the top front) with a piece of clean waste fabric like calico or cotton, to remove any lint or thread dye particals which can build up. I also use a felt circle under my thread spool as it helps with the thread running smoothly off the spool, I'll lift this off and clean underneath and around the back where the spool sits as the dust/dirt builts up here too.

I also throw out the needle after each project is finished, a needle is good for 6-8 sewing hours at most, depending on the material sewn. If you hear squeaking or popping when stitching slowly, your needle is blunt. Also watch for burrs on the needle tip, the needle does all the work so it pays to be fussy and change regularly. And use the correct needle for the project, sharps for wovens, ball points for knits and jerseys, and the right size, ie a 60 or 70 for very fine fabrics like organza and chiffon, 80 for poplins, 90 Jeans for denim, and 110 for very heavy materials like coatings and curtain/upholstery.

And keep magnets away from electronic machines, don't have a magnetic pin cushion on the free arm, not good for them.

Janome Hello... | 372 views | 0 helpful votes


check with sewvacdoctor.com or A1sewingmachines.com and see if they can help you with a manual.

Janome Hello... | 300 views | 0 helpful votes


the thread is most likely binding somewhere in the path. Pull out thread, use canned air or compressor to blow out path and rethread.

Janome MyLock... | 318 views | 0 helpful votes


if you look closely there is a very tiny hook that comes through the back of the needle. That is what catches the tread to pull it through the needle. Sometimes it will get bent to the side. Using a pin or needle, very carefully move it back to its centered position

Janome Memory... | 132 views | 0 helpful votes

Not finding what you are looking for?
Janome Logo

43 questions posted

Ask a Question

Usually answered in minutes!

Top Janome Crafts & Hobbies Experts

R.A. Ellis
R.A. Ellis

Level 3 Expert

12730 Answers

Carolyn Rogers

Level 2 Expert

109 Answers

thinksewfast

Level 2 Expert

89 Answers

Are you a Janome Craft and Hobby Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...