Jacuzzi Popular Questions, Answers, Tips & Manuals

Maybe these folks can help they stock allot of Jacuzzi parts.

Can't Find It?

Send us a picture Text a photo: 305-321-3420 https://www.guillens.com/catalog/shop/Jacuzzi/Bath/Repair-Parts/Control-Boxes/mfr-3BU?pagenum=1

If you have any clamp on amperage meters, you need to see what the amperage draw on the circuit is when it is running. This will tell you if something is wrong with the pump circuit. It could be anything from a bad capacitor to an impeller obstruction.

No, replace the whole thing. That is bad design and inferior parts. Ask Moen to replace it under warranty. They might say No, but then again, they might know of a fix or if they had a bad batch of plastic parts.

Hi, Please attempt to start the jacuzzi without any water and see if it functions. Then you can fill the jacuzzi up to 1/4th with water and check if it continues to run. If so, continue to one half full. If this jacuzzi breaks down at these water levels, then you'd need to call the manufacturer to advise on what part needs to be changed to get everything working again. Thank you.

https://www.youtube.com/watch?v=XE6r7V80Rzg

yes the are and parts are available on line.

they twist out

Hello, Several things can cause this problem- if you post a picture of the inside of the tank so we can have a good look at how the fill/stop mechanism operates that would be great. We could more than likely identify some type of problem and solution. Not all flush/fill mechanisms are not the same but thats surely where your problem is UNLESS its in your water lines. I would love to help you just please provide photos and as much information as you can. Good luck! Mr.Mike

pump -impeller failure /bearings /motor failure

rollout switch on lower inside cover by burn rack and gas valve possible down draft pushed flames into cabinet and tripped it if keeps happening might need chimney if ok check gas pressure if low unit overheated or burner tube clogged

Impeller may be broken or clogged. Turn the pump off and remove the basket. Reach back into the pump with your fingers and see if you feel debris. If you can't reach or if there is debris you will need to open the back of the pump, take off the diffuser, and clean out the impeller.

There may be a video but you should be able to tell by looking at it too big screw under tank holds valve on big screw under tank holds valve on see: https://reviewmotors.co/jacuzzi-dual-flush-toilet-repair-parts

Without knowing the code it could mean anything. Consult your owners manual or online manual for error codes and remedies.

Contact the Dealer and seek qualified tech service. Risk of electric shock/***** You should not take the risk but have a QUALIFIED SERVICEPERSON perform the work.

If there is power to the unit, most likely it will need to be replaced. Check for reset button, and check the fuses before replacing the unit.

These switches that are mounted to the tub itself are usually air switches when you push the soft button it puffs air into a solenoid somewhere near the motor causing it to activate the pump, and there is a possibility that the pump motor has a reset button on the end of it to kick it off if something would cause the pump to jamb, hair,toy, jewelry or whatever that somehow got sucked into the intake

Should be one on the motor and also check to see if there is a GFCi somewhere too. Could be around where the jacuzzi switch is.

replace switch

The flashing on/off light in a Jacuzzi whirlpool bath may indicate an issue with the control system, and it's important to address the problem to ensure the proper functioning and safety of the whirlpool bath. Here are some general steps you can take to troubleshoot the issue: 1. Check the Power Supply: - Ensure that the whirlpool bath is receiving power. Verify that the circuit breaker for the whirlpool bath is not tripped, and check for any loose or disconnected power cords. 2. Inspect the Control Panel: - Examine the control panel for any visible issues, such as loose or damaged wires, connectors, or buttons. Ensure that there is no water or moisture present in the control panel area. 3. Reset the System: - Some whirlpool baths have a reset function. Turn off the power to the unit, wait for a few minutes, and then turn it back on. This can sometimes reset the control system. 4. Refer to the User Manual: - Check the user manual that came with your Jacuzzi whirlpool bath for specific information on troubleshooting and resetting the control system. The manual may provide insights into the meaning of the flashing light and how to address it. 5. Contact Jacuzzi Customer Support: - If the issue persists and you cannot find a resolution through the manual, contact Jacuzzi customer support or the manufacturer for assistance. They may be able to provide guidance on how to troubleshoot and resolve the issue. 6. Professional Inspection: - If you're not comfortable or able to identify and fix the issue, it's advisable to seek assistance from a qualified professional or a technician experienced in Jacuzzi whirlpool bath systems. They can perform a thorough inspection and diagnose and repair any electrical or control system problems. It's essential to prioritize safety and follow proper procedures when dealing with electrical components and water. If you're uncertain or if the troubleshooting steps don't resolve the issue, it's best to seek professional assistance to avoid potential hazards.

the motor could be seased, can you get to back of motor to see if it's spinning