Jackson Popular Questions, Answers, Tips & Manuals

1)Temperature is more than 90-100degree means the steam will comes from the rinse arm automatically (as u indicated thermostat chances is there)
2)check the heater contactor is getting switched off interminently(if it is not getting off problem on thermostat)

Maybe and probably. Speak with your Jackson distributor about this. He probably has a solution for you that is compatable with your equipment.

Thanks for your interest in FixYa.com

Hi


Thanks for using FixYa. Please check for the following if your dishwasher is not working--


1. Fuse (blown or tripped).
2. 120 VAC supply wiring connection faulty. Repair or replace wire fasteners at dishwasher junction box.
3. Electronic control board faulty.
4. Motor (inoperative, check resistances).
5. Door switch (open contacts).
6. Door latch not making contact with door switch.
7. Touch pad circuit defective.
8. No indicator lamps illuminate when START or OPTIONS is depressed.


Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks
Rylee

Raise the saddles on the FR to help take away the fret buzz. Check the neck for curve. If the neck has a VERY slight bow on the fretboard side the strings will be able to vibrate better without buzz. Also might want to step up to a heavier gauge string set if you play in lower tunings.

look for the fot surface ignitor . it has probably failed and will require replacement. it will be located in or about the burners ( in center ) . or to left of center .. do not touch the ignitor when installing ..or bang it on anything . they break easy. mm

any farm store or auto parts should have an inner tube, you will just need the size of the tire

What you are hearing turning is the pump motor. The manual feature is for deliming the machine and and locks the unit in wash mode only.

It is likely your fill solenoid has malfunctioned if no water is entering the tank in a normal cycle.

please disregard this request for help. thank you.

could possibly be a bad micro switch, a bad contactor or even a bad capacaitor on the motor

You will need to take the cover off of the breaker panel. Find the three lugs that the incoming hot wires are hooked to. With three phase you will have three hot lines. Check the voltage between the phases. L1 - L2- L2- L3- and L1 - L3 Also check the voltage from each line to ground. If you havw 120/208 three phase current you will have 208 +or- a few voltage between the phases and 120 or so from each line to ground. If you have 120/240 three phase you will have 240v across the phases and 120 to ground on two legs and 208 to ground on one leg, this is called a "wild" or high leg. You may also have 480v into the shop and you will know that very quickily if you get 480v between phases. No matter if you have another voltage, you can buy a trandformer that can convert whatever you have to 208/120 3 phase for your unit.

your furnace must have one. look to see where the large filter, that is the fresh air intake. it does not have to be out door air, just air.

Look for the BTU rating. 12,000 BTU is a one ton unit.

Hi,
I hope this link is what you need:

http://www.woodsequipment.com/WorkArea/showcontent.aspx?id=10937

The problem is hard water not soap. There is a new product out called the dishwasher filtration system. It filters the water before it enters your dishwasher. It works amazing and has a money back guarantee. You will love the way your dishes look after the first load. It is also very affordable (like 70 bucks). Go to www.dishwasherfilter.com to find out more info.

the fill valve is easy just take the coil off and there is a hole in it put a metel screwdriver in the hole and turn the unit on if it pulls the screwdriver like a mganet it works is more likely i bad diaphram now as for the draining it drains bu turning a valve dirverting the watter from the pump down the drain hose so you must have a hole or leak in the hose

they are located under the front panel of the machine they should be lablet , usually they are by the timer cam

Hi,

The best solution would be to contact their support team.

[email protected]


The mailing address, phone and fax number is :-


Mailing Address:
Jackson MSC LLC
P.O. Box 1060
Barbourville , KY 40906
Phone:
800-736-8144
Fax:
606-523-1799

However, in order to request for parts, you need to contact :-

Service 888-800-5672
THAT WOULD BE THE BEST OPTION.

Unless email them for parts at :-

[email protected]

For technical support besides the first email, you can also send them an email at :-

[email protected]

There are so many web options. However i would advise you to contact Jackson
directly.

Thanks for using "Fixya".

Hello, here is their web page www.jacksonprofessional.com/

I would bet that the actual tools are out sourced to specific manufactures.

Good luck, Jack

please clarify your question

it is cycles, delime. enter .cycles