Jackson Recent Questions, Troubleshooting Help & Support

The sensor for the door (top right behind flashing) is no longer working. $48 part. 1 Hour service.

Well, while I must admit that "Percussive" maintenance, sometimes works, as you have discovered there is more to servicing than, just "Giving it a good whack" lol.
The problems with these units, is usually to do with the Thermostat, and/or the Main Controller Board, the MCB, is prone to "Spikes". "Surges", and mains borne problems.
The first thing to replace should be the Thermostat and or sensor thermistor. Usually we replace the Thermistor, or Temp Sensor, and, try that first, and if no go, then the Thermostat itself, and then if no go, the main Board. I provide you with a parts supplier below. Below that is the Jackson support website to assist you. Please contact them, and ask for a referral to an authorised repair center. Then ask the repair center for a "Quote" for the repair before allowing any work to commence. If you do not wish to DIY.
http://www.whaleyfoodservice.com/jacksonmachineparts.aspx
http://www.jacksonmsc.com/?xhtml=xhtml/jac/us/en/homepage/default.html&xsl=homepage.xsl

However it is my professional recommendation that you call a professional to attend to this matter.

Hi,
That could be either the motor or the heating element...
You will need to check it out with an Ohm meter to tell for sure what the exact cause is...

heatman101

Perimeter = sum of all sides. If you have a square that is 40cm on every side it would be 4x40=160cm

The Fender pick up has two wires, blue and white. The Jackson has four: red, green ,black, and white.

1st. Determine the hot wire and the ground wire on the Jackson pick up and then just replace the Jackson pup with the Fender pup. White on the Fender is the hot lead and blue is for the ground. If you hook it up backwards it will be out of phase with the other pup's and will sound thin and weak when selected with either the rhythm pup or the lead pup. Of course, by itself it will sound normal because switching the wires only changes the phase of the Fender pup.
On the Jackson pup, the green and black are ground while the white and red are the hot side. Just solder the white lead of the Fender pup to the pup selector hot side and the blue lead to the ground.

It should say on the back of the box or give some indication as to the settings but in general you can gague it from the flow rate and or the granual size but a rough setting is about 5 to 6

could possibly be a bad micro switch, a bad contactor or even a bad capacaitor on the motor

please clarify your question

you may need to clean out your hot water heater depending on how old it is and yes 80 gal should be more than big enough adj. thermostat to the next level

If not enough water is coming out of arms, there could be build-up in the arms or the tubing to the arms. Check that the filter is not clogged as well.

you will need to raise the temp on your hot water heater

It's a Dinky.

Try this site:

http://forum.emgpickups.com/viewtopic.php?f=2&t=2249

contact knight chemicals

Hello there:
Water-heating cycle Many dishwashers heat the wash and/or rinse water to a higher temperature, as the cycle calls for it. In these cycles, the dishwasher pauses after it has filled with water, waiting for the water to reach the pre-set temperature. What happens next, depends, as follows: On some units, the pause is timed and the unit continues after the allotted time. On others, the cycle can't continue until the water reaches the higher temperature. If you have this type of dishwasher and the water isn't being heated (say, because of a problem with the heating element or thermostat), after the unit stops at the heating cycle, it never continues. When you repair the heating-system problem, the "cycle problem" is fixed too. Timer Timers don't often fail. But if every other part of the dishwasher seems to be working properly and the timer knob seems to be stuck in one place--doing one function continuously--the timer may be at fault. Dishwasher timers can't be repaired. If yours is defective, replace it.

Yes welding arc is a much brighter light and it will work fine for you.

What you described is normal for that helmet. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/sean_54c3a3dc48a7773c

Ward Leonard systems used be used in most elevators and a lot of cranes. While I am not familiar with your machine I'm sure you could refer to a modern crane parts list and find types and detail compatible with your motors.

Hi


Thanks for using FixYa. Please check for the following if your dishwasher is not working--


1. Fuse (blown or tripped).
2. 120 VAC supply wiring connection faulty. Repair or replace wire fasteners at dishwasher junction box.
3. Electronic control board faulty.
4. Motor (inoperative, check resistances).
5. Door switch (open contacts).
6. Door latch not making contact with door switch.
7. Touch pad circuit defective.
8. No indicator lamps illuminate when START or OPTIONS is depressed.


Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks
Rylee

Maybe and probably. Speak with your Jackson distributor about this. He probably has a solution for you that is compatable with your equipment.

Thanks for your interest in FixYa.com