Jackson Dishwashers - Popular Questions, Answers, Tips & Manuals

Sounds like the valve itself is stuck open. Shut off the water to the dishmachine, remove the solenoid coil, get a pipe wrench or large crescent wrench and open the top of the rinse valve. Either get some muriatic acid or some strong lime away and clean the internal valve. Make sure to put the parts back in the correct way. The top of the valve has a piston and a spring. DO not lose either of them. The bottom of the valve has a diaphram and a valve seat. remove both of these clean them so that they move freely. Install all the parts exactly like you found them. Tighten down the valve, put the coil back on and turn on the water

Most likely something is stuck in the pump Impeller

sounds like pump or motor failure

Contact the manufacturer. FIXYA uses unpaid volunteers throughtout the world who try to answer questions for free. FIXYA volunteers do not work for manufacturers or sell washing machines or other appliances. Phone: 888.800.5672 Mailing Address: 6209 N U.S. Hwy 25E Gray, KY 40734 Online form to send questions: https://www.jacksonwws.com/contact/ Contact Jackson WWS

THIS could be your huckleberry! It is item 3 of suspects... Also note ITEM 7, "heater delay relay"? Disconnecting and reconnecting MAY be resetting that relay!? ALSO BE VERY AWARE OF THIS: BEFORE the heater element can be energized, the rinse booster heater MUST be initially filled with water. Damage to the heater element will occur if the element is not submerged in water! Here's your thermostat: Jackson 5930-003-13-65 THERMOSTAT, 120-170 DEGREE "WAS" Find it here: Jackson 5930 003 13 65 THERMOSTAT 120 170 DEGREE WAS $137.11 plus shipping OR SAVE SOME LOOT AND GO HERE: eBay: Jackson thermostat 5930-003-06-48 175-195F Item location: Camano Island, Washington, United States eBay: 122938835291 $129.50 INCLUDING SHIPPING! Get your MANUAL here: http://www.jacksonwws.com/wp-content/uploads/2016/08/Delta-5E-manual.pdf text: 'TEMP WASH AND RINSE: 120 degrees' >>> 140 degrees recommended for BOTH (see page 3). <<< TROUBLESHOOTING on Page 16 and 17! "Wash temperature not at required reading." 1. Check that white/blue wires are connected. 2. Defective thermometer. 3. Defective thermostat. 4. Rinse heater defective. 5. Defective heater contactor (R2). 6. Incoming inlet water temperature below required minimum. 7. Defective heater delay relay (R4) See ANOTHER GREAT troubleshooting chart here! http://kitchen.manualsonline.com/manuals/mfg/jackson/delta_5_d.html?p=21 $50 please... JUST KIDDING Anthony

Is it possible someone has accidentally leant on the door? I would take side panels off and check if hinges are bent

Try Ali Baba web site they have a lot of hard to find parts you must use any numbers on original part or mfg part # .

You have neglected to include the model number which you must have if you have the manual. Jackson produced a number of models. That said, here is a site that may help you because it shows where parts go in a schematic: Wash Rinse Assembly Contact Jackson WWS

all height modifications are possible i dont care what anyone else says it can be done. If you need further help, reach me via phone at https://www.6ya.com/expert/scott_8b3f0f0fc5f566a7

google the manufacturer for user manual and parts information as for quality detergents there are catering and commercial cleaning outlets that will have the products that meet standards you have to decide on the quality verses cost that still meets standards

Confirm that the lid switch a common failure is working. A distinct click is usually heard when lid is closed. Temporarily by-pass to confirm and diagnose this type of problem. Confirm tab is in place on the lid.

Before replacing motor check that the relay (2) is operating and is providing power to the motor. The link is the manual for the washer. Check the wiring diagram at the later section page 62 Hope this helps? https://www.jacksonwws.com/wp-content/uploads/2016/11/7610-002-49-79D_JP-24-SERIES.pdf

Replace the solenoid

Are you sure you have 3phase power available? there should be 220 between all three.

how about some more info. Does the soap pipe have a clog in it? Try putting a lenghth of wire down it to check for clogs. Also, run a load of full strength vinegar through the machine. Turn off the water supply, set the machine on to a point past the fill timer, then add at least 1 gallon of pickling vinegar, then turn on the machine. Stop it before it discharges and drains the vinegar, and reset it back to the beginning of the wash cycle. Do this several times until the wash water gets gunky, then let it complete the cycle after you have turned the water supply back on. Check the soap pipe now. Frankly, I have never heard of a soap pipe so I wonder if this is really your issue. do you perhaps mean a spray arm? At any rate, a good cleaning like this should solve your problem. BTW, if you do not want to use vinegar, try a package of lemon jello or a purchased product called Lemi-Shine both of which you run through your machine to clean it iout.

Why is there an Oven clock on a dishwasher? If genuine check Manual or manufacturer, or service agent.

duplicate - already posted.