Isuzu Popular Questions, Answers, Tips & Manuals

A better search would be by 'year make model diesel'. https://www.google.com/search?q=Isuzu+3kr2+diesel+cylinder+head+bolt+torque ..

no year car, no hope. surely you know that or tell you VIN and we tell your the dealer of the car will not talk to you lacking a VIN see why? (parts and manuals and all facts key off that VIN)

Ah there you are with the vehicle details. Ignore the first link Veronica https://www.google.com/search?q=Isuzu+Ascender+fold+rear+seats ..

usa CAR? ,NO VIN, NOR IF IMMO FITTED i WILL rtm to you, service manual on said LOCK 16 STEPS THERE ARE.: Turn the steering wheel so that the vehicle's wheels are pointing straight ahead. Turn the ignition switch to LOCK. Disconnect the negative battery cable, and wait at least 5 minutes. Disconnect the yellow 2-way SRS connector located under the steering column. WARNING The wheels of the vehicle must be straight ahead and the steering column in the "LOCK" position before disconnecting the steering wheel. Failure to do so will cause the coil assembly to become uncentered which will cause damage to the coil assembly. Remove the engine hood opening lever and steering lower cover. Remove driver knee bolster (reinforcement). Loosen the inflator module fixing bolt from behind the steering wheel assembly using a Torx® driver or equivalent until the inflator module can be released from steering assembly. 1. Inflator module 2. Steering wheel 3. Steering column cover 4. Combination switch and SRS coil assembly 5. Snap ring 6. Cushion rubber 7. Lock cylinder assembly 8. Instrument panel lower cover 9. Driver knee bolster (reinforcement) 10. Shift lock cable (for A/T) 42050 images-42050_rode_g0027 Disconnect the yellow 2-way SRS connector and horn lead located behind the inflator module Apply a setting mark (1) across the steering wheel and shaft so parts can be reassembled in their original position, then remove steering wheel Move the front wheels to the straight ahead position, then use steering wheel remover J-29752 to remove the steering wheel WARNING Never apply force to the steering wheel in direction of the shaft by using a hammer or other impact tools in an attempt to remove the steering wheel. The steering shaft is designed as an energy absorbing unit. Remove steering column cover. 12. Disconnect the wiring harness connectors located under the steering column. Remove the combination switch assembly with SRS coil. NOTE The SRS coil is a part of the combination switch assembly, which can not be replaced separately. Therefore, be sure not to remove the SRS coil from the combination switch assembly. Remove snap ring. <<<<<<I GUESS YOU ARE HERE? Remove the rubber cushion. Remove shift lock cable (for A/T). Disconnect the starter switch harness connector located under the 16:steering column then remove lock cylinder assembly.

buy the service manual in you unstated country is best;.

are you in Africa.? Isuzu cars are dead in USA< no sales for long long time, a bakkie/???? 2002 - 7????????? no year told either. NOT 220D no start, cranks fast. sure. the kb (faster) has like 30 engines world wide and 50 model names from FASTER . but there are 2 engine used, and not told you. 2.2 L 115 hp (85 kW) C22NE / 22LE I4 Or the GM engine? so complex this the wiki can not even cover all this variances KB 220 double cab 2005? 2.2L petrol spark engine, sure In lyrical they call , cranking Swinging, what laugh that is. it doesnt start cranked, and yes spark is fire as is combustion. but spark must be good is the cam belt old and slipped.? GENERIC answer lacking all useful facts. test spark first, as all PCM cut fuel is spark fails. so spark is first and you can not burn petrol (gasoline ) lacking spark so we test spark (using test spark plug method 100 years old>? use sprayed in intake, starting fluid (instant start in a can) runs for 3 seconds, 3 times tried, sounds GOOD and yes now find out fuel pressure is zero cranked. that is is a tool all shops have and use all day long. now year car, wow

TELL WHAT WILD MEANS tell all the good and the bad cold and hot engine, parked or driving or on hills, or stalls or tell it all. good cluck

The Crankshaft Position sensor is normally located in the timing cover or on the side of the block with a cylindrical portion that inserts into the block

Hi, Please call your local advanced autoparts to learn about the interchangeable alternators available for your car. They supply these type of parts so they would be good for this. You can call them by dialing 1 (877) 238-2623. Thank you.

It is a guess, but try pulling the back of the seat squab forward as it is probably hinged at the front. They need to be accessed easily and quickly. https://fuse-box.info/isuzu/isuzu-ascender-2003-2008-fuses-and-relay ..

USA car yes/no?? 2002 Isuzu trooper. 2wd or 4wd? check engine lamp on means scan the OBD2 scan port and it tells you of VSS sensors are bad, some car have 2. fuses farst scan it next./ C10 and C15 fuse must not be blown out. dash box. marked as Meter and Audio, ignore names, 10 and 15 fuses both good. electronic, speedo it is. and same for VSS vss for 2wd not same as 4wd, 2wd is on rear of transmission , manual stick or autmatic 4wd is on rear of transfer case. not telling your drivetrain makes for long answers engine>>>trans>>>transfer case. non of that told at all VSS is the speed of the far rear , prop drive shaft. it converts, RPM of said shaft to MPH, (speed) and then sends said speed directly to Speed and to the PCM and TCM if there is a TCM

NO car told at all, maker model and enigine there. what side does the driver sit, left or right , in USA ,its left. not told if clamp is stock powerful and good OEM spring loaded clamp or these cheezy screw drive clamps sounds to me like 2 causes 1: yes clamp is bad. 2: engine has exhaust gases in the coolant,. (blown head gasket) or worse warped head or cracked head. worse can go more. worse. a $1 fix or $1500 fix. why not ask a real shop to check it out. they can a radiator leak down test in a jiffy, a cheap tool we all have. knowing what is or having #2 get worse and blow up a $3000 engine is not wise. find the truth then play the cards. avoid cascaded failures get it tested by a real shop. normal pressure is about 14psi, or 1 bar. the rad cap regulates that and does not blow off hoses with good clamps. but if #2 happens all bets are off.

When the brake booster light and brake light come on after replacing the batteries in a 2017 Isuzu NPR Diesel, it could indicate a problem with the brake system or a malfunctioning brake booster. Here are some steps you can take to troubleshoot the issue:

1. Check the brake fluid level: Low brake fluid level can cause the brake booster light and brake light to come on. Open the hood and check the brake fluid level in the reservoir. If the level is low, top it up with the recommended brake fluid and check if the lights go off.
2. Check the brake system: Inspect the brake lines, brake pads, and brake rotors for any damage or wear. If the brake pads are worn out, replace them immediately.
3. Check the brake booster: The brake booster is responsible for increasing the force applied to the brake pedal. Check the brake booster for any damage or wear. If the brake booster is malfunctioning, it will need to be replaced.
4. Reset the brake booster light: If the brake booster light and brake light stay on even after checking the brake fluid level and inspecting the brake system, it may be necessary to reset the brake booster light. To reset the brake booster light, turn the ignition switch to the "on" position without starting the engine. Pump the brake pedal 3 times, then turn the ignition switch off. Start the engine and check if the lights go off.

If none of these steps work, it is recommended to take the vehicle to a certified mechanic or the nearest Isuzu dealership for a professional diagnosis and repair.

all 4 dead , 4 corners? and hazard switch turned on , too. do the 2 lamps cluster fail tool Left/right turn? 2002, check fuses first? marked ( turns, blinker/ signals/)? most cars today have no such thing, (the old skool blinker modules are gone due to magic of BCM computer is just pure software loops) 2002 Isuzu Axiom in what country? seems this car has one. https://www.rockauto.com/en/catalog/isuzu,2002,axiom,3.5l+v6,1378953,electrical,flasher,10139 im in the service manual on like and this chapter is missing(sadly) under dash some where; guess driver side.

no info generic answer if line [brake] is damaged replace it and box possible abs control [module]

Question edited for clarity (order), spelling and add maker. Question moved to model category. Videos and parts supply https://www.google.com/search?q=1991+Isuzu+Trooper+2.6.+Thermostat+location ..

If it is available for free it is here. The website Scribd has it for cost. https://www.google.com/search?q=isuzu+8pe1+engine+ecu+pinout ..

Battery clamps. Most likely ground but check both. Air Filter possible staving for air. Get reading from OBT.might help. If it has one? Is there an idle adjustment?Check for vacuum line leaks. PS Also check for the ground cable from engine to frame or body. usually a braided flat unwrapped/uncoated ground strap, if it has one.Larry

Hi, Please check your alternator as well. I would also get a full diagnostic scan of your system from your local autozone and use the error codes to guide you in further pinpointing the cause of the car-start issue. Thank you.

https://www.carparts.com/blog/p0847-code-transmission-fluid-pressure-sensor-switch-b-circuit-low/