IBM Lands Phones - Popular Questions, Answers, Tips & Manuals

be a part of human

If you have more than one phone, phones 2-n need to be assigned different codes from the first ... Since the default phone code is '11', assign them with '12', '13', etc. via 1012, 1013, etc.

http://www.ebay.com/sch/i.html?_odkw=IBM412CD&_osacat=0&_from=R40&_trksid=p2045573.m570.l1313.TR0.TRC0.H0.XIBM412CD+power+adaptor&_nkw=IBM412CD+power+adaptor&_sacat=0

Press the third button from the left on the top row of buttons (labelled <Erase>). The LED panel will display "Del MW Indcator <Erase>: confirm". Then, press that <Erase> button again and the MW (Message Waiting) light will stop flashing.

That is an indication that device is almost depleted to battery source. Refer from the user guide to ascertain what parts are required acquirable from retails.

Hello

It seems that the handset is not linking up with the base unit. As it is a cordless phone the handset has to be on the same frequency as the base unit. Please read the User Guide and set the same frequency on both, the base and the handset. Then only it will do everything it is supposed to do.

I doubt you will be able to get just a handset, however all may not be lost, try opening up the handset, i think you may find what has broken away is the speaker, and most likely it has broken the wires off, or maybe it's the battery, if it is one of these it's a pretty simply job, to relocate and resolder the wires back on, and you may just get your unit working again.
Also if you don't wish to DIY, why not take it back to Walmart and ask where to get it repaired and then get a "Quote" for the repair first.
maybe if ya were real nice, they may even exchange it for another.. just act dumb, and say I dunno how it happened it just don't work...lol can I get a replacement.. I mean it's Wallmart, they are there to serve? aren't they.

Hi.

you can download or view the manual here

its in PDF format when you open it, Click the save icon (diskette icon) on the top left hand side to save it to your PC

hope this help

Judging from what I have seen online, this is a common problem (mine does the same). Only solution that seems to work is get rid and buy something else! Seriously. Sorry...

Follow the instruction from the manual located at this url http://www.wedophones.com/Manuals/Aastra/IBM-412%20Four%20Line%20Phone%20User%20Guide.pdf

clear all active and inactive call forwardings. after that it will not norward any calls.

You have the ability to transfer an outside call to any extension within your phone system.
1. Press the [TRNSFR] button during your conversation
2. Dial the desired extension or press one of the Direct Station Select (DSS) buttons
3. One ring will be audible a transfer is successful. Otherwise, two rings will be heard
4. Any extension can pick call transfer
5. The Call Transfer mode will automatically cancel after 10 seconds if no transfer number is dialed

cHARTER CABLE IS NOT SENDIN CALLID . GIVE THEM A CALL.

Of course there replacement.Check the manual of your phone get the adress of the company and call the customer care they will tell you where to get the accessories

The phone is maybe too far from the base. You can also try to use the find button on the base to «call» the phone the first time so it can find it. There is also a another way for the base to find the phone and it should be indicated in your manual. I know we had this problem with ours and we had the procedure in our manual but I suppose it is not the same for all the phones. Also... make sure the phone line is connected to the base... ;)
Good Luck.

http://www.wedophones.com/Manuals/Aastra/IBM-412%20Four%20Line%20Phone%20User%20Guide.pdf

The above pdf file would guide you with your phone as its the manual for the same.

Thanks
Have a nice day and please donot forget to rate this.

According to page 5 of the IBM-900SP manual, it's a 3.6V, 600mAh Ni-MH battery pack, model GP60AAAH3BMX.

You need to register the base and handset... Here is how to do it:

Press and hold the "CH" button on the right side of the handset and the press and hold the "Page/Find" button on the base.... The handset should say "Registered" in a few seconds

Try unplugging power, and see if this simple reset can help.

The 2.4 spectrum only has 3 channels that don't overlap. There are a total of 14 channels in all. Channels 1,6,11 don't overlap with other devices. Set your wireless access point to 6 (strongest channel) and your phone to another non-overlapping channel (1, 11). That should solve your problem. If it does not, then one of the devices you have is not digitally tuned and is causing interference on neighboring channels. The proximity of the phone's base station in relation to the wireless access point or laptop can also have an effect especially if the spectrum is dirty. Hope this helps!