Hyundai Electronics Popular Questions, Answers, Tips & Manuals

did you give them the right address because you are not on the right page here for these comments This fixya site and you got nothing and there is no service from this site

https://www.hyundaiusa.com/contact-us.aspx

Why don't you ask this IT person to achieve correctly its installation ?

the spark cord i presume. the spark cord screw out of the magneto module.

1st resolder inverter board, if the problem still exist chek the flex cable.

Just replace all capacitors in power section,try to replace the power button with one of menu or etc. if there are more than one button`s,somethimes the button is going bad.

chek power inverter board. and find inverter driver

If you have a new car then there is a section in the owners hand book that details on how to set the clock

The cost will reach to 2/3rd of the total cost of the device.

If you can find a setting for DDC/DI and turn that OFF, this could solve your problem (it did for me). Description of the setting is included below, but put simply it allows your monitor to communicate with your computer and make adjustments.From wiki: The Display Data Channel or DDC is a collection of digital communication protocols between a computer display and a graphics adapter that enables the display to communicate its supporteddisplay modes to the adapter and to enable the computer host to adjust monitor parameters, such as brightness and contrast.

Press and hols the Volume Dn button on the front panel of the TV and display button on the remote control at the same time for about 5 seconds. If you wish to know more procedures to enter service mode to Hyundai TVs, check this link.

Check or replace the Blower Fan fuse/relay in the cars fuse box.

p1014ap06

You have bad capacitors in your tv set that will need to be replaced.

is your lcd in english? what do you mean you ccant find indonesia on the menu? are you looking for the language or the indonesian channel? well if your looking for the language you should go the settings menu and go to language..from there try to find indonesia and enter,then the language will be indonesian..or if your wondering why you cant scan the channels on your lcd..you should try settings menu again and go to the channel set up..find auto scan and click it..then your lcd should be scanning and remembering all the channels thats been scanned,but before you do the scanning make sure that your antenna or your cable provider is connected to your tv..otherwise you wont scan anything

Hello! The Brake Light Switch is the likely culprit...Check fuse # 8 (10A) Dash fuse box first...On the Brake Switch connector; The Pink/Black wire should have 12 volts when brake is depressed...If it does the second choice is the Shift Lock Solenoid isn't pulling...Lets check the first choice and eliminate it before moving to the next...Send a comment...Guru...saailer I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

How can I connect wii to alba tv 19 inch

first off is it an oem raido we are talking about or is it an aftermarket raido if it is oem you can try the dealer but if its aftermarket you are better just buying a hole another raido and lertting a pro installing it for you

It the typical symptom of dying power supply due to bad DC filter caps. You need to open it up and inspect them first.

If you are going to DIY and already try the monitor with another PC, and have proper tools and know safety precaution then please read on: Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply (they should be replaced in a set), blown fuses; poor solder joints, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed monitors to get some ideas what to look for: http://s807.photobucket.com/albums/yy352/budm/ Post back what you see inside so we can guide you further and it will help out other people in the future also.

Basic LCD monitor and TV troubleshooting guide: http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide http://www.fixya.com/support/r7406380-tv_training_manuals Failed TV and Monitors pictures: http://s807.photobucket.com/albums/yy352/budm/

Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague

Capacitors kit: http://lcdalternatives.auctivacommerce.com/ he can make you a set of caps for you. Or www.digikey.com just make sure to use caps with low ESR, 105c, high ripple current, long life rating such as PANASONIC FM or FC series.

Hi.

It is not a lose wire. If problem was a lose wire or a bad solder joint it would have been sensible to vibration and the TV would have turned off when touched.

It is not a software problem either. The software cannot turn off the TV completely, at most the TV would freeze or go in standby.

If TV goes off completely, the problem is usually a defective PSU in rare situations a defective inverted can also give similar problems.

The problem is usually the PSU, A component (usually a capacitor starts failing) The other capacitors in PSU can compensate the work that is not being done by the defective part, and the PSU works for a while, until problem starts happening more often and TV does not turn on at all. In some case a defective inverter can do the same. In that case the inverter oscillator section is defective. The problem with the inverter is very uncommon.

Check the power supply. Sometimes it is possible to see at a glance a burnt spot or capacitors bulged on top. If there is nothing at a glance the PSU should be tested before replacing it.

PSU part number is PSCV121106B the PSU is not available anymore, the repair must be done replacing the parts on PSU. Below the repair kit with the components. For safety reasons the repair must be done by a trained person.

Here the repair kit: Repair Kit PSU PSCV1211068

Regards.

Ginko