Hyundai Televison & Video - Page 5 - Popular Questions, Answers, Tips & Manuals

Hello
There are tow reasons for this fault with Hundai sets. The first one is with "Reset", and the second one is with its power regulator circuit board. As the set is now in OFF condition and no screen is available to get a reset option, the fault will be due to the power regulator board itself.
Open your TV, and locate the power switching regulator board. It can be located very easly, as power cord will go diretly to it after the main panel ON/OFF switch. I'll give you a picture of the picture of a typical power board here. Usually these board are irrepairable, and must replace it as card basis. Check for any bulged capacitors, as shown in the picture, in the power board. If so; replace them. This is the only repairable thing with these type of boards. If there are no such capacitors seen, unplug out each pluged in connections on this board one by one and reconnect it. If any loose connection proble is ther, doing this will rectify it.
If nothing helps you, replace the board. This board will have a number printed on it, which should be noted when buying anew one. The board can be bought from most of the electronic sparepart shops at your town. It can also bought from the Authorised Service center for Hundai also. OK.

The same place as where u put in the Soap or liquid deturgents after the first rinse cycle.

Hello,

The issue you describe is consistent with a power supply board issue. This is the board where the AC goes to. This problem may have occurred as a result of irregular power supply, or excess power supply or power surge.

The TV is receiving current but cannot circulate or transfer the current to other necessary part of the TV because of the defective power supply board. You might be lucky it's just a blow fuse. Also a defective transformer can cause your TV not to power on.

All these can be checked on the power supply board.

But more often bad capacitors causes problem on the power supply board. I do not think the power board needs replacement, rather those defective capacitors is causing this issue. Open unit up and take a look at the power supply board.You will probably see one or more electrolytic filter capacitors that are bulged up in the top-not perfectly flat like the others.

The value of these capacitors will be different, most likely they will be somewhere around-820 to 2200uF/25 V( or /10V sometimes)

You can replace them with same values but I would recommend the voltage rating to be higher(like 35V for an original 25V) for reliability purposes.

What happens is,these bulged top capacitors will cause a low and unfiltered DC voltage=main board will malfunction(the relay will keep clicking until the caps are holding enough charge to bring the voltage up over a threshold point).

You can buy these capacitors at any Fry's or Radioshack store or you can order them online at vendors like "mcmelectronics.com"(look for electrolytic capacitors). After replacing these capacitor(capacitors) most likely the normal operation will be restored. Or you can by a refurbished complete power board to save you some stress.

Note: There may be also some other causes for this symptom ,like a defective T con board ,or main board,but the bulged top capacitors are the most common cause for this issue.

If you don't know about TV repairers, take the TV to the nearest repairman to fix the fault for you. Also, note that TV stores a lot of current, so wait a while before opening the TV back cover.

I hope this helps.

Make sure all the cords are plugged in and not frayed but,
Something about LCD's is that the lightbulb may be going out...this can be very expensive but uo might be able to get it from the manufacturer's website
--

Best Regards Lauren940

The surge may have scramble the mother board, try unplugging it for about an hour to let it reset itself, if that does not work, then you may need to replace the main board.

If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on: Basic LCD monitor and TV troubleshooting guide: http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting http://www.fixya.com/support/r7406380-tv_training_manuals Failed TV and Monitors pictures: http://s807.photobucket.com/albums/yy352/budm Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague Parts: www.shopjimmy.com Parts: www.interliquidparts.com Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx he can make you a set of caps. Or www.digikey.com, just make sure to use caps with low ESR, 105c, high ripple current and long life rating such as PANASONIC FM or FC series.

well you should call a sky installer

In most cases when the CD does not play it is possible that the optical head is a suspect. Sometimes it might pick up ordinary audio CD but will not play other formats. This indicates that the optical head is weak and so there is no detection or scanning of the CD . If the optical is working the tracks will be read immediately but with no scanning the laser head can be defective.

The main motor will not work in some cases as unless the tracks are read the drive motor will not work with signal from the processor. Also in some cases the central motor base can shift and so the distance to the disc can be more resulting in low detection. You can pull up the spindle to come closer. Sometimes certain cleaner disks will not be tracked to run for cleaning as it will not be read and so will reject. Hence it is ideal to manually clean the laser head eye using a cleaning swap /cotton bud with gentle pressure on the lens eye.If there is no result then watch if the CD spins or tries to spin. If so the board seems to work unless a test is taken on the main board but the possibility of a defective optical head can be the suspected fault.If any of the above seems otherwise we must recheck with possibilities of a malfunction of the main processor board

Hi

CI stands for common interface, there will be a slot on the side of your tv for a CI Module to be inserted, this allows you to view encrypted channels (such as ESPN) that you have to pay for using servces such as topup tv (uk).

It sounds like you have being trying to watch a encrypted channel without a CI Module inserted, this would most likely be the cause of the error message you are receiving.

Hope this helps

The plasma screen is literally burned down - used up, worn out, whatever you want to call it. This is a sign that the screen is near death due to its age and not a defect. There is nothing that can be done to save it, the tv is dying.
Time for a new one.

Go to the picture setup of your settings menu.
Somewhere in there are options for selecting picture size.
The options will be similar to: Normal, Wide, Zoom, Stretch
You have probably selected Zoom, try Normal.

I'm sorry for the difficulties you're experiencing in getting the Closed Caption on the TV. Most probably the Closed Caption might be disabled from Cable Box in your Case. Please enable Closed Caption from the Cable Box Settings to resolve the issue.

Note: Please refer the manual of the Cable Box to get the instructions to change the Closed Caption Settings on the Cable Box. You may also provide me the model # of the Cable box if you're experiencing difficulty in finding the option

If the issue persists, please unplug the TV for more than 5 minutes and then reconnect and check the operation.

Thanks for understanding. Please let me know if you require any clarifications.

Try to adjust the vertical hold trimer.In adjusting the trimer you look the screen while adjusting the trimer until the screen or picture back to normal.

Problems with these TVs not turning on are usually capacitor related. Take the back off then look on the power supply where the power chord goes look at the fuse next to the plug. See if it's physically dark if so, the fuse is most likely blown and you should just look up the board number on E-bay for a new power-supply for a more costly, but easier fix than a repair shop. While the back is off, look for capacitors that are puffed and see if they need to be replaced. There are usually 2 caps by a heat sink that look bulged.
http://cgi.ebay.com/10pcs-Electrolytic-Caps-KIT-16V-50V-0-1uF-1000uF-/290505738749?pt=LH_DefaultDomain_210&hash=item43a37dc9fd#ht_1734wt_905
and
http://www.youtube.com/watch?v=Mm51C_RDIZE vid one http://www.youtube.com/watch?v=BNHHrgX_6cs&feature=related vid two.
Should be enough info. If you're not into soldering and you feel comfortable replacing the board, there is this.
http://cgi.ebay.com/Sony-FWD-32LX2F-Power-Supply-pt-715T2123-1-NC-/120640216067?pt=LH_DefaultDomain_0&hash=item1c16b79c03

If this doesn't work, you're going to have to change the power supply. Or get it repaired for
195-230 dollars.

Please try 0863 for Hyundai Televisions To program your Sky remote control using the 4 digit code

1. Switch on the TV set
2. Press the TV button on the Sky Remote
3. Hold down the Select and Red buttons for 2-3 seconds until the LED blinks twice
4. Press the TV button on the Sky Remote again
5. Enter 0863
6. The LED should blink twice, if not recheck the 4 digit code used and go back to 1
7. Press the standby button on the Sky Remote (The TV should go to standby)
8. Press the Select button to store

If the TV does not go into standby press the TV button then the standby button, then TV then standby, keep repeating this until successful. This will scan the codes used for a particular make of TV.

Please keep me posted.

Thanks.

Lor04

Hi,

If your TV won't turn on, you should check the power cord. Make sure that it is securely in the wall plug. Sometimes the power cord has burned out and needs to be replaced. You may also want to check the batteries in the remote to make sure it working , if otherwise power supply board is dead, you know basic electronics' and soldering? Most of the times, the power supply board just have dead leakages gases capacitors.These capacitors always bulges up on it top,or puff up on it top.Replaced these gases leakages capacitors will get your TV power stable,and work again.Or tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.

I hope this will help to fix the fault and do take care in handling the set......

I was told it is the deflector curcits, HOT, Horizontal IC

Si te refieres a que el televisor no se enciende, entonces esta es la solución.
Hay una buena probabilidad de que no tienen condensadores electrolíticos, ya sea en la etapa de potencia o la sección del inversor o de ambos.
Todas las tapas en estas secciones que se ven abultados en la parte superior, o abultados / fugas en la necesidad de fondo para ser reemplazado.
Si repetidamente se enciende, con el tiempo probablemente se quedará, pero cada vez que lo apaga, la TV será más difícil y más difícil de poner en marcha hasta que un día simplemente no lo hará.
A veces hay que hacer lo contrario para poner en marcha y desconectar por 5 minutos, a continuación, intente.
Si usted no es experto tecnología, esta unidad tiene que ir a reparar.
Si usted es hábil con un soldador y puede identificar la fuente de alimentación y el inversor / sección de FM para las luces de fondo, un puñado de condensadores baratos probablemente le arreglamos bien desde arriba.
Coincidir con la capacitancia de los condensadores. Ir más tensión si se puede, y todavía tienen que encajen.
IE - no es una mala idea para reemplazar una tapa de 10V con 16V, pero no reemplazan una gorra de 680uF con un 500uF o 1000uF (a menos que sean positivas es sólo hacer la ondulación de filtrado).

That can be the bad T-CON board, look at my guide to see the example of it.
http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide http://www.fixya.com/support/r7406380-tv_training_manuals Failed TV and Monitors pictures: http://s807.photobucket.com/albums/yy352/budm/ Parts: www.shopjimmy.com

First make sure its not the connection from any video devices. And if the connection is fine and there is still no picture the plasma has burnt out in the TV.
You will have to have it repaired or consult your warranty to see if there is anyway to get the TV fixed.

Try these for Hyundai TVs:
0037, 0865, 0556, 0706, 0860, 0753, 0698,1376