Husqvarna Recent Questions, Troubleshooting Help & Support

Also check fuses, they are located on the left hand side of the Machine. They are accessed by tilting the seat Forward. They are ?at pin Fuses of the same type used in automobiles. There are two fuses with ratings and functions: 20 amp Primary Fuse 7.5 amp mower deck coupling

Removing the deflector on a Husqvarna YTH2348 lawn tractor can vary depending on the specific model, but the general process should be similar. Here are the steps to remove the deflector on your Husqvarna YTH2348 lawn tractor:

1. Park the tractor on a level surface and set the parking brake.
2. Locate the deflector on the tractor. It is usually located at the front or rear of the tractor, often attached to the hood or the deck.
3. Locate the fasteners that hold the deflector in place. These may be screws, clips, or pins, depending on the model.
4. Using the appropriate tool, remove the fasteners that hold the deflector in place. A screwdriver or pliers may be needed.
5. Carefully lift the deflector off the tractor.
6. To reattach the deflector, align it with the mounting points and secure it with the fasteners.

It's important to consult the operator's manual for specific instructions and diagrams for your tractor model, as the deflector location and the procedure to remove it may vary depending on the make and model. It's also important to consult the operator's manual for safety instructions.

If the fuel bubble on your Husqvarna 125 BV blower is not priming the engine to start, there could be a few potential issues causing this problem. Some possible causes include:

1. A clogged fuel filter: The fuel filter is responsible for removing dirt and debris from the fuel before it reaches the carburetor. If the filter is clogged, it can restrict fuel flow and prevent the engine from starting.
2. A clogged carburetor: The carburetor is responsible for mixing fuel and air to create the combustion that powers the engine. If the carburetor is clogged, it can restrict fuel flow and prevent the engine from starting.
3. A problem with the fuel line: If the fuel line is kinked, pinched, or has a leak, it can restrict fuel flow and prevent the engine from starting.
4. A problem with the fuel tank: If the fuel tank is not properly sealed, it can allow air into the fuel system and prevent the engine from starting.
5. A problem with the primer bulb: If the primer bulb is not functioning properly, it can prevent fuel from reaching the carburetor.

It's recommended to check the fuel filter, carburetor, fuel line, fuel tank and primer bulb. Clean or replace them as necessary. It's important to consult the operator's manual for specific troubleshooting instructions and diagrams for your blower model, as the location and procedure may vary depending on the make and model. It's also important to consult the operator's manual for safety instructions, and to make sure you have the correct parts for your blower. It's recommended to seek the help of a qualified technician if you are not familiar with this process.

There are two idle screws one high, and one low. Your high adjustment idle screw needs to be adjusted.

check and test the safety switches

A foot pedal for a Husqvarna Viking 1610 sewing machine can be obtained from several sources:

1. Sewing machine dealers: Many sewing machine dealers, especially those that specialize in Husqvarna Viking sewing machines, carry a wide range of replacement parts, including foot pedals.
2. Online retailers: Websites such as Amazon, Ebay, and SewingMachinesPlus carry a wide range of replacement parts for older and newer sewing machines, including foot pedals for the Husqvarna Viking 1610.
3. Husqvarna Viking: You can contact the manufacturer Husqvarna Viking to find the nearest authorized dealer or to purchase parts directly from the company.
4. Specialty stores: Some specialty stores that focus on sewing machine parts carry a wide range of replacement parts, including foot pedals for older and newer models of sewing machines.

Check with an authorized Husqvarna Viking dealer. Check Husqvarna Viking website for dealer closest too you.

I'm sorry to hear that your Husqvarna 125B blower isn't starting. Here are a few things you can try to troubleshoot the issue:

1. Check the fuel level in the tank. If the tank is empty, fill it with the correct fuel mixture (50:1 ratio of gasoline to oil). If the fuel is stale (more than 30 days old), drain the tank and refill it with fresh fuel.
2. Check the spark plug. Make sure the spark plug is clean and properly gapped. If the spark plug is dirty or damaged, replace it.
3. Check the air filter. A dirty air filter can restrict the flow of air, causing the engine to run poorly or not start at all. Clean or replace the air filter as needed.
4. Check the carburetor. If the carburetor is dirty or clogged, it can prevent the engine from starting. Clean the carburetor or have a professional service it.
5. Check the ignition system. If the ignition system is not functioning properly, the engine may not start. Check the ignition coil, ignition switch, and any other related components to make sure they are working correctly.

If you have tried these steps and the engine still won't start, it may be necessary to take the blower to a professional for further diagnosis and repair.

There is usually one source for this problem, and it's easy to fix. Take the end cap of your machine as if you were changing a light bulb. Now you are off...When you switch from straightstich to zigzag, the levers operate across and inside the body so that the needle shaft, you watch it going up and down, can also move sidesways (but only a few mm's (about 3/16 inch)) The needle shaft should both go left and right, freely. It is hinged at the top but half way down ththe shaft it "floats" in a two sided guide. This sounds complicated but it truly is NOT. What happens to neglected machines is that "gunge" forms in the sliding parts and stop the left and right deflections. You my need to prise open the shaft from it's guide to start with (be gentle) but a few drops of oil normally soon allows the needle shaft to slide side to side. When you can shake the needle shaft from side to side BY HAND (with the machine set in the zigzag mode) replace the end cap and start zigzaging. And in future oil your flaming sewing machine.....

FIRST TIME EVER USED IT ? 6.5h ENGINE HERE.got spark, THIS IS FIRST, using fresh plug to test.got fuel? or is it super old fuel.canT burn gas , lacking spark , the engine may have compression release just like huge single cylinder motor cycles have, and can fail. but just harder to start failed.ASK MAKER FOR HELPTOP CAUSES (BY ACTUAL USAGE FAILURES)SO THIS TOOL SITS LONG TIME UNUSED? NOT TOLDBAD OLD FUEL AND FILTERS AND CARB. DIRTY.ENGINE IS 2CYCLE , GAS AND 40:1 OIL MIX OR PER MANUAL.FUEL FILTER PACKED, AIR FILTER PACKEDspark plug fouled, put in new. and gap it.and this.EASYSTART SYSTEM.The engine and starter are designed to ensure quick andeasy starting of the machine. Reduces the pull resistancein the starter cord by up to 40%. (Reduces thecompression during startingSEE PAGE 6https://www.lsengineers.co.uk/media/advice_centre/Husqvarna/Power-Cutters/operators-manual-k970.pdfSEE PARTS.https://www.husqvarnaconstruction.com/us/power-cutters/k970/?article=967348001

There could be a few different issues that could cause your Husqvarna Diamond sewing machine to display a "need to rest" message and not start sewing. Here are a few things you can try to troubleshoot the problem: Check the machine's power supply: Make sure the machine is plugged in and the power cord is securely connected to both the machine and the outlet. Check the machine's threading: Make sure the thread is correctly threaded through the machine and the bobbin is correctly installed. If the threading is incorrect, it can cause the machine to stop sewing and display a "need to rest" message. Check the machine's tension: If the tension is not set correctly, it can cause the machine to stop sewing and display a "need to rest" message. Try adjusting the tension and see if that resolves the issue. Check for any debris or lint buildup: Lint and debris can accumulate in the machine and cause it to stop sewing. Clean the machine according to the manufacturer's instructions to remove any debris. If you have tried these troubleshooting steps and the machine is still not sewing, you may need to have it serviced by a professional. It is always a good idea to follow the manufacturer's recommended maintenance schedule and have the machine serviced regularly to keep it running smoothly.

A good fuel mixture ratio for any 2 stroke weedeater or chainsaw is 50:1. That equals out to 2.6 oz of oil per gallon of gasoline. Most 2 stroke oils can be bought in pre-measured containers at hardware stores or small engine dealers. It is best to not mix more than 2.5 gallons at a time. Hope this helps, Daniel.

I don't have this machine, but mechanical items with moving parts need to be oiled. I would check in your users manual. It should give you a schematic on the places to oil. Use sewing machine oil so it doesn't get all gummy and cause more problems.

Try this - remove all the transmission oil from the transaxle and put in a heavyer oil - 50 wt.
see if your transaxle has a drain plug - if not you will need to remove the tranaxle from the lawn tractor. I had to try a ratchet strap to the rear of the tractor and lift it up until the wheels were free. I removed the brake linkage spring, the fwd/rev linkage, and wheels. Undo the axle bolts and two screws ofn the cross support bracket on the tranaxle mount. pull the vent fill plug on top of the transaxle and turn the transaxle upside down to drain all the oil from it into a pan. Refill with 50 wt. to the top and remount the transaxle back in place. Next you will need to bleed the system as follows:
1. Have the tractor on jack stands with rear wheel off the floor.
2. Start engine on low speed.
3. repeat open and closeing the bypass valve while alternating the forward and reverse pedals.
4. when wheels start to turn increase the engine speed.
5. repeat quick forward or reverse with panic braking stops until transaxle gets full responce.
6. remove jack stands and have tractor on the wheels.
7. recheck the oil level again.

I did this to mine and it will improve your tractor ability to climb hills like new. 30 wt oil is too light (good for brake in) when tractor was new and refilling it with 50 wt will work like new or better.

Check that the stitch length is set to make ~10 stitches per inch. This stitch is long enough to actually move the fabric. If the stitch length is set too short, the fabric will stay barely move and the needle will stitch almost in place. Check that the feed dogs have not been dropped for darning or free motion quilting. In this position, they do not rise and are, therefore, unable to contact the fabric to pull it through the machine. With the presser foot raised and using no fabric, hand rotate the handwheel and watch if the feed dogs actually drop down below the needle plate, move toward the front of the machine, then rise above the needle plate, and move toward the back of the machine. If the feed dogs are moving in this manner, then they are functioning properly. Is there lint or gunk stuck in the feed dogs? This will restrict the ability of the feed dogs to grip the fabric. Are the feed dogs worn? Are the little teeth worn so there are no sharp points? What type fabric are you using? If it is very light-weight or slick fabric, the feed dogs will have a difficult time gripping the fabric. Most machines have a presser foot pressure adjustment so that more pressure is applied between the presser foot and the feed dogs. Consult your Owner's Manual. The adjustment is usually a dial either on the left side of the machine, on the front of the machine located above the needle bar, or on vintage machines it is usually a skrew located under the top lid above the needle bar. ...

to much slack worn--wrong belt--replaced incorrectly -----their is an adjustment on the actuator pulley very slight and slight adjustment on deck brackets

Owner's Manual only. https://www.google.com/search?q=Husqvarna+Viking+Classica+100+Service+manual Check out videos 3 and 4. https://www.google.com/search?q=Husqvarna+Viking+Classica+100+reverse+not+working ..

Did you adjust the bobbin tension first? Sewing machine tension is a delicate tug of war between the bobbin holding onto the bottom thread and the top tension pulling it to the centre of the fabric. The 8:51 video is the best one that explains and shows how to do it. https://www.google.com/search?q=bobbin+thread+tension+adjustment ..