HP LaserJet - Recent Questions, Troubleshooting & Support - Page 3
Hp 4700 49.3066 service error
49.xx errors are mostly caused by invalid print commands, corrupt
data, or invalid operations. Basically the printer "does not understand" the print job.
- restart the printer to clear the print job from the printer's memory.
-if the error returns disconnect the network/USB cables from the unit and cycle power again.
If the error comes back without the network/USB connected perform a cold reset on the device and go the next step.
- Once the unit is at Ready reconnect the network/USB cable.
If the unit gets the 49.xx error or begins to print a job then gets the error disconnect the cables again and power cycle the printer. This time when you plug the network/USB cable in watch the control panel for any signs of the unit receiving a print job. When the printer says "Processing" press the cancel button on the printer. This should clear the "bad" print job.
I strongly recommend updating to the latest driver for the device
Drivers Software . If you had an issue with a PDF file use the Post Script (PS) driver.
Good Luck
Having a problem with a hp 4700 printer. when
To get your printer working again, try the following fixes:
Lose packaging or protective strips
When you're about to install a new toner cartridge, there are orange protective strips and plastic clips that are there to make sure the cartridge isn't damaged whilst being transported. Each of these clips and protective strip across the drum must be removed before installing your new toner, otherwise they will prevent your printer from printing.
Clips are easy to spot and stick out like a sore thumb. The protective strip is on the side of the toner and has an orange ring that must be pulled to remove the strip. It may also look like a piece of cellophane like it does in the image below.
Squashed Metal contacts
So a printer can detect a toner cartridge that has been installed, 2 tiny metal contacts must connect to the corresponding contacts on the cartridge. The metal contacts in the printer and the ones on the toner complete a circuit. If the contacts aren't touching, your printer will think that the toner isn't installed.
Remove your toner cartridge and have a look for something that resembles a microchip or two metal squares. Now visualise where these would connect inside the printer and look for the corresponding connectors inside the printer (making sure the printer is switched off and unplugged).
If the two metal connectors seem squashed back, gently (so not to break anything), pull them forwards. This should allow them to correctly connect to the toner once you install it again.
It's also possible that losing bits of packing material or paper jams can cause an issue so make sure the printer is clear before installing a new toner. Also if using a remanufactured cartridge, double check that the micro chip is securely in position, isn't dirty and that nothing is obscuring it.
Broken plastic pieces
If a toner cartridge has been damaged along one of the sides so that the plastic slots have broken off, then it may not correctly sit inside the printer. Similarly to the previous reason for the supplies memory issue, the contacts won't correctly connect, and the only way to fix this problem is to replace the toner cartridge with a new one.
Out of date firmware / software
Your printer manufacturer will regularly update your printer with new software of firmware. If the software is out of date for any reason, you may get an error. Visit google and type '[your printer model] firmware' in the search bar and download the latest one for your computer / printer. Once updated this can often fix many printer problems. You can find the latest firmware updates on the HP website here.
One final possible reason for the supplies memory error message can be caused when you install a compatible or remanufactured toner cartridge and the data stored on the cartridge micro chip is out of date.
The printer firmware can then deliver the supply memory error message and the only way to fix this problem is to get the company you purchased the cartridge from to replace it with a new one.
This may help you,
Rachel Gomez
How to clear paper jam in output bin
The printed page comes through the hot fuser at the top of the printer, through the exit rollers an end up in the exit bin.
We cleared a massive paper jam out of the fuser, by removing the grey surround on top of the printer. The plastic hooks that hold it in place get broken in the process, then you will the jammed paper between the fuser rollers, and the exit rollers. A technician can do it for you, but is unessersarly costly.
9/23/2022 3:59:34 PM •
HP Color...
•
Answered
on Sep 23, 2022
Hp laser jet printer 2055 ,52 scanner error how can solve it please
The HP Printer error 52 indicates with scanner. When you see the HP printer error code 52, then follow the steps:
·Turn off the printer
·Wait for 30 seconds and then turn on the printer
·In case the 52 error is still coming up on the printer, then make sure that the Flatbed scanner assembly is replaced
·In case the error is still being shown, the Scanner/Laser assembly may also require replacement.
Find the more HP printer error codes and their solutions. If you need any help to fix the issue contact HP Printer experts.
Very Light Printer on HP Color LaserJet 3500
Table 7-33. Causes for distortion or blurring
Cause Solution
Transfer unit is defective. Replace the transfer unit. Calibrate the printer
after replacing the transfer unit. See Calibrate
Now, later in this chapter.
Defective secondary transfer roller If it does not rotate smoothly or it is deformed,
replace the secondary transfer roller.
DC controller PCB is defective. Replace the DC controller PCB. Calibrate the
printer after replacing the DC controller. See
Calibrate Now, later in this chapter.
Calibrate Now
Use the following procedure to calibrate the printer whenever you replace the DC controller,
the formatter, the color misregistration sensor (PS12), the transfer unit, or the laser/scanner.
1. Press to enter the MENUS.
2. Press to highlight configure device.
3. Press to select configure device.
4. Press to highlight PRINT quality.
5. Press to select PRINT quality.
6. Press to highlight CALIBRATE NOW.
7. Press to select CALIBRATE NOW.
8. Wait for the printer to calibrate.
hope this helps
pdouglasss
9/23/2022 8:01:10 AM •
HP Color...
•
Answered
on Sep 23, 2022
When I try to install
I think you are connecting it through Network cable. And it happens at time that its not being detected because of the Internet Security program you are running as the computer takes it as foreign address.
I would like to assist you further in it.
How do I fix a 59.53 error code - HP LaserJet 4700 Printer
- Display:
- 59.53 ERROR
- Description:
- Yellow image drum motor startup error
- Remedy:
- Reconnect the connector J18 of the yellow drum motor and the connector J120 on the DC controller PCA. Perform the drum-motors component test in the DIAGNOSTICS menu. If the message persists, replace the yellow drum motor.
Error code is 2753
Hello,
Error #2753 is not a real code number for the HP 3055!
Please Visit here to check any other error codes regarding this machine here;
http://h10061.www1.hp.com/ccsearch/search?pname=HP+LaserJet+3055+All-in-One+Printer&qry=error+code+2753&submit.x=0&submit.y=0&ctry=us&lc=en&dlc=en&mode=lz&tmv=0&method=prodFinder&pid=1140780&productBigSeriesOid=12012&spid=1140612&opname=HP+LaserJet+3055+All-in-One+Printer&pname_desc=HP+LaserJet+3055+All-in-One+Print%2FScan%2FCopy&ptype=commercial&stype=pn&contextual_lname=&spname=HP+LaserJet+3055+All-in-One+Printer&temp_hql=s-001%2Cs-002%2Cs-004%2Cs-003%2Cs-005%2Cs-006%2Cs-017%2Cz-001%2Cc-002%2Cc-001&search=0
Good Luck!
Rich Lilja
My hp laserjet 1300 printer shows blinking the orange light instead of the green one and I couldn't find out what is the reason
1. Go light/button blinks twice with solid green and orange lights
2. Green light starts blinking with go light twice and then both go off
3. orange light goes off.
4. green light followed by orange light followed by go light cycle twice and a third time by the green light
5.followed by the orange light continuously blinking.
I have already tried the following trouble-shooting:
1. Put in a new cartridge
2. Made sure there is paper properly seated in the tray
3. Made sure all doors closed (I even took off left side to verify no memory cards
4. Verified all doors closed
5. Done a cold reboot by holding the Go button while turning the unit on.
6. Repeated steps 1-5 multiple times.Hope It's resolve all Your Printer Problem,
Or
Still having Problem Then follow Us For
HP Support
Hp 5550 dtn 10.00.00 supply memory erro
the chip is faulty on the black cartridge, change the black and it'll work, alternately you can out it diagnostic made and run without the cartridges being monitored
HP LaserJet pro color MFP M276N Network lan port no working
Troubleshoot the wired network connection
Make sure you are using an undamaged Ethernet cable, check for a green light near the Ethernet port on the printer, and then print a report to verify the connection.
Turn off the printer, and then disconnect the Ethernet cable from the router and the printer.
Check the cable for damage, and then verify that it is an Ethernet cable and not a phone cable.
NOTE: Ethernet and phone cables look similar, but Ethernet cables are usually bigger and have eight visible wires on the connector.
Reconnect the cable to a different Ethernet or LAN port on the router, and then connect the other end to the printer's Ethernet port.
Turn on the printer.
Check the lights on the printer's Ethernet port to make sure the connection is successful. The green light should be steady, and the orange activity light should blink.
Print a Wireless Network Test Results or Network Configuration report.
Inkjet printers with a control panel menu: Open the Wireless, Network Settings, or Setup menu to locate the list of available reports.
Most inkjet printers without a control panel menu: Press the Wireless and Information buttons at the same time, or press the Wireless and Start Copy Black buttons at the same time.
LaserJet printers: Press and hold the Wireless button for 10 seconds or until the Ready light blinks, or go to the Wireless menu and select Wireless Network Test.
Laser NS and Neverstop Laser printers: Press and hold the Resume and Wireless buttons for 3 seconds.
DeskJet 6000 and 6400, ENVY 6000 and 6400, and Tango printers: Touch and hold the Information button until all control panel buttons light up, and then touch the Information and Resume buttons at the same time.
Make sure the Network Status is Ready, or follow any instructions to resolve network issues identified on the report.
Regards,
Rachel Gomez
How to clear memory on HP P3015
Before starting, note down the IP address if its network printer..
1. Turn the product off.
2. Turn the product on. When the memory count begins, press and hold the OK button. Continue holding down the OK button until all three product control-panel lights flash once and then remain on. This might take up to 10 seconds.
3. After the message SELECT LANGUAGE appears on the display, press the button or the button until COLD RESET is highlighted.
4. Press the OK button. The product performs a cold reset and then continues its power-on sequence.
5.Chk & set I/O settings..if required..
Hp 2300 laserjet printer error code 13.20.00
this problem persist NVRAM resetting
To perform an NVRAM initialization, complete the following steps:
1 Turn off the printer.
2 Press and hold (DOWN arrow), and turn on the printer.
3 When all three status lights are lit, release (DOWN arrow) and press (UP arrow).
4 Press PAUSE/RESUME. The first item of a menu appears.
5 Use (UP arrow) or (DOWN arrow) to scroll to NVRAM INIT, and press (SELECT).
cihat ALTIN FROM TURKEY ANKARA
Have HP Laserjet 2300d (Q2474A) printer that won't
Make sure the printer is plugged into a functioning wall outlet supplying the proper voltage (110V or 220V).
If you are using a surge protector, extension cable, or power strip, plug the printer directly into the wall outlet.
Press the power button to turn on the printer.
If the issue persists, unplug the printer and wait 15 minutes.
After 15 minutes, plug the printer back in and press the power button.
If the issue persists, try a different power cord (if available).
Regards,
J Wick
Not finding what you are looking for?