Hotpoint Logo

Hotpoint Answered Questions & Fixed Issues

Do you work here? Claim your company

  • 532 Products
  • 82K Answers
  • 2M Views

It sounds like an over temp sensor is tripping.....Make sure the lint filter is clean and no lint is blocking the vent pipe.........A fire hazard is present so be careful......Unplug the Unit while servicing the vent piping...........

Hotpoint Washing... | Answered on Apr 20, 2019 | 23 views


CHECK SCREENS IN THE END OF THE HOSES .

Hotpoint Washing... | Answered on Apr 10, 2019 | 30 views


Best to contact the manufacturer or an appliance repair service. This is a car forum and we wouldn't have knowledge on you gas dryer.

Hotpoint Dryers | Answered on Mar 28, 2019 | 29 views


It depends on the reason for the hot smell - discovering this would mean a trip to the service shop and weighing the cost of that against a replacement microwave.

Unless your Hotpoint is something special, it is likely a replacement would make sense.

It is wise to periodically measure the power output of a microwave oven by timing the boiling of a measured quantity of water when it is young. When or if the time has extended more than about 10% it is time to think about service or replacement. It is also important to keep the inside of the cabinet clean and all the air vents clear.

Hotpoint Washing... | Answered on Mar 25, 2019 | 31 views


Go to www.repairclinic.com and enter WDL5490. With luck, you will be presented with a list of common replacement parts/assemblies and may be able to view a generic Hotpoint video showing disassembly with part/assembly identification.

Hotpoint Dryers | Answered on Mar 22, 2019 | 34 views


  • F05 - Pressure switch jammed on full
  • Thing to do check pump is not blocked and clear it then reset machine by unplugging for 5 mins and plug back in if still gets error F 05 then you need a repair call out. hope this helps.

Hotpoint Washing... | Answered on Mar 19, 2019 | 3,489 views


Using your belt, slip it under the agitator. Give a very hard yank and the agitator will pop up and off. DO NOT HAVE YOUR FACE OVER THE AGITATOR WHEN YOU PULL ON IT. It can pop up with force, and end up breaking your nose! So be careful!

Hotpoint Washing... | Answered on Mar 15, 2019 | 59 views


I had this problem and discovered it was due to a leak. The float switch attached to the bottom panel was operating. Pull out the mains plug, tip the machine on it's side (water will escape so get a mop ready), remove the bottom panel, 3 screws front and back, disconnect the connector from the float switch. Tape the connecter up out of the way and stand your machine back up. Try running it now. If you have a leak somewhere then you will get a puddle under the machine. If no leak, then I would suspect the float switch itself.

Hotpoint 24 in.... | Answered on Mar 29, 2019 | 11,208 views


There is a problem in the system, read the error codes.

Hotpoint... | Answered on Mar 09, 2019 | 34 views


Has it got a "reset"button? If not you could of damaged the circuit board

Hotpoint Washing... | Answered on Mar 04, 2019 | 27 views


Zero is cold enough. Fridge gets its cold air from the freezer Make sure that the passage between the two are not blocked'

Hotpoint... | Answered on Mar 03, 2019 | 833 views

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Hotpoint Experts

Sal De

Level 3 Expert

2699 Answers

Marvin
Marvin

Level 3 Expert

84543 Answers

Brad Brown

Level 3 Expert

18031 Answers

Are you a Hotpoint Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...