Hotpoint Popular Questions, Answers, Tips & Manuals

If the off button doesn’t respond and cut it off, replace control / clock.

I would try unpluging the unit for about 10 minutes to see if it would revert to defaults

Most likely a control board issue

You may think u have checked all but underneath there is a black soft rubber hose and sometimes a sock can get sucked into this and stops draining worth a try if not maybe your pump is gone

I once bumped the water supply shut-off under the sink and turned the supply off at the shutoff. Other than that, have you had any work done on the hot water tank recently ?

I also encountered a similar problem. It was not possible to contact the service center, so I searched for a solution on the Internet, and found it on this site - https://washingcodes.com/blog/#.XFwRwFUzaUk

Remove the hose to the sensor switch at the tub end and check for obstruction. The small container on the side of the tub may be clogged. Clean with a small drill or piece of wire.

You are obviously not putting it back right or has something fell down the back

Probably a defrost problem or fan in freezer isn’t working. Any frost buildup on inside back freezer wall?

Most likely cold control thermostat is bad and needs replacing

Hi there, I am from the UK so model numbers vary but all basically the same. Do not fear it is simple really. You need to take the door from it's hinges first. It will either have screws or bolts to the door or frame of the machine. Now you have the door dismantled and in your hands. place upside down and you will see screws ??? they will be situated around the door ?? the door comes in two parts and the glass is sandwiched between the two parts. ( Take photo if in need ) you will see see a metal shaft and spring where your handle will fit. All the best and Happy Christmas from the UK

There should be a wiring diagram inside console where timer and switches are.

Make sure that the fan is not obstructed and the area is clean. I know a man who bought a new freezer because his old one quit working. While taking out the old one, found a mouse stuck in the fan. Cleaned everything up and the freezer worked for 10 more years.

https://manualzz.com/doc/2057104/hotpoint-vtd-6000-clothes-dryer-user-manual Here's your diaGRAM

https://removeandreplace.com/2016/02/02/refrigerator-display-panel-is-blank-not-working-how-to-reset/ Try resetting the display and see if it starts working again.

https://www.google.co.in/search?q=Have+Hotpoint+Dishwasher+model+DF61N+Need+wiring+diagram&rlz=1C1KMOH_enIN790IN790&tbm=isch&source=iu&ictx=1&fir=hfT4fUt27enaFM%253A%252CqTo0BQBDnQ0BcM%252C_&usg=AI4_-kSIDXjWgo94dL3QyAmXQKmlBHCuTQ&sa=X&ved=2ahUKEwiBisX1v_7eAhXDrI8KHfE-AMMQ9QEwAnoECAYQCA&cshid=1543662915079001#imgrc=hfT4fUt27enaFM:

This is a sign that the transmission is failing, If you post the model number we may be able to help you further.

feel the sides and the back of the freezer if the out sides are not warm or hot then there is a good chance that the compressor is not working

Hotpoint is made by GE. Call 1-800 GE CARES with your model #.

Without testing I would suggest that the heating element has shorted to earth enough to take out the RCD. You should test with a multimeter between the element and the outer sheath which should show 0 if Faulty and replace the element, otherwise it is something else in the circuit i.e. temperature cutout causing the earth leakage.