Honda Logo

Honda Popular Questions, Answers, Tips & Manuals

Do you work here? Claim your company

  • 3K Products
  • 292K Answers
  • 5M Views

Check on line or on "you tube" for spark plug gap.

Honda... | 20 views | 0 helpful votes


How long has it been since it had a new fuel filter?

Honda Cars &... | 19 views | 0 helpful votes


I would suspect that the inverter is fine and would look towards carburetion. The inverter, in addition to supplying the correct voltage and current, monitors the current being drawn by your connected load. It controls that stepper motor on the top of the carburetor and increases the throttle to increase the engine power to support the load. (Mechanical power in = electrical power out.)
Start the generator and then add a small load to the outlet, 100 watt light bulb or something. I use a space heater that I can turn on just the fan. See if it still stays running. Then increase the load (with my heater I go from fan only to the first level heat 1000w) and watch the top of the carburetor to see if the inverter increases the throttle to compensate for the increased load. By the sounds of what you are describing, it will go to full throttle and the engine will die because of a restriction on the available fuel. If that is the case, take the carb off and clean it. Or if you are not the carburetor rebuilding type, buy a new one.. they are only about $80. Not a bad fix for a $2000 generator :)

Honda Electrical... | 52 views | 0 helpful votes


It could be the drive belt. If it requires replacement, there is a squealing sound.
A simple replacement should take care of the sound.

Honda Civic Cars... | 31 views | 1 helpful votes


You might need to have your hatch latch checked. There is a micro switch in the latch that registers when it is closed. If this switch is not operating, the system will think the hatch is open when it is actually closed.

Honda Cars &... | 29 views | 1 helpful votes


Hi there's this website something like reliable-store and it is very amazing for manual for repairing servicing anything
someone on fixya recommended it to me and I thank him even today
They have full manuals and it's verrrrry cheap and mine
I got free in offers
3rd time I bought it, I also had an issue with the file so the girl replaced it in 30 mins
there is one website more but i don't remember its name it was 2 years back bitman something link this
Try these out brother

1995 Honda Civic | 26 views | 1 helpful votes


Hi, Steve for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://goldwingdocs.com/forum/viewtopic.php?t=11720
Honda Tech Talk How to Bleed Your Brakes
https://www.manualslib.com/manual/817941/Honda-Goldwing-Gl1500.html
https://www.partsfish.com/page/oem-parts-for-yamaha
https://ownersmanuals2.com/honda/gl1500c-valkyrie-1997-owners-manual-60951
Instant Repair Help over the Phone to speak to me personally $6

1999 Honda F6 C... | 48 views | 0 helpful votes


The Honda 5.0 gc160 owners manual calls for an NGK BPR6ES for proper heat range. Should be available at any Lawnmower shop or online at ebay

Honda Electrical... | 37 views | 0 helpful votes


If we had the codes we could be of some help.
This pose will have a list of the code numbers and what they mean.


https://www.odyclub.com/forums/28-1995-1998-odyssey/36761-abs-trouble-codes.html

Honda Cars &... | 24 views | 0 helpful votes


Low oil pressure will cause the tappets to chatter and in worst circumstances, the main bearings to become noisy. I would complete an oil and filter change using the recommended grades from your owners manual first. If still noisy, it is probably down to poor/lack if servicing and too late to stop.

Honda Accord... | 20 views | 0 helpful votes


The presence of a stored P2413 code means that the powertrain control module (PCM) has detected a malfunction in the exhaust gas recirculation (EGR) system. The EGR system, used in ODB-II equipped vehicles, is designed to help reduce nitrogen oxide emissions in engine exhaust, so the answer is no

2005 Honda Pilot | 42 views | 1 helpful votes


Hi, Marcelo for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.fireblades.org/forums/general-discussion/103738-how-do-set-ignition-timing-cbr-600-a.html
https://www.motorcyclespecs.co.za/model/Honda/honda_cbr400rr%2087.htm
http://staging.isi.org/honda_cbr_400_manual.pdf
https://www.partsfish.com/page/oem-parts-for-honda
Honda CBR400 Wikipedia

1989 Honda CBR... | 16 views | 0 helpful votes


Temperature actuator for driver side stuck.

Honda Cars &... | 175 views | 0 helpful votes

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Popular Products

1992 Honda Accord
1992 Honda Accord

2,940 Questions

1991 Honda Accord
1991 Honda Accord

2,649 Questions

1995 Honda Accord
1995 Honda Accord

1,606 Questions

1996 Honda Accord
1996 Honda Accord

1,608 Questions

1998 Honda Accord
1998 Honda Accord

1,531 Questions

Top Honda Experts

Marvin
Marvin

Level 3 Expert

84540 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14640 Answers

Brad Brown

Level 3 Expert

18031 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...