Hitachi Answered Questions & Fixed Issues

Did you know that this site https://fmovies.dev updates movies frequently and you can watch them for free?

These batteries have big problems that Hitachi doesn't address very well. Unlike NiCad batteries, Lith-Ion ones must be periodically used and recharged to retain their battery functions, i.e. if they have been sitting on the shelf at a store for an extended period of time, chances are they will be dead when bought and will not accept a charge. If they go dead i.e. no little red light on the charger when you plug the battery unit in...it's basically junk.

If you can return them or exercise the warranty do so. If / when you get new ones DO NOT completely discharge them like you would NiCads. Lith-Ion batteries do not have the "battery memory" issues that NiCads have which means you don't lose running time if you don't fully discharge the battery unit prior to recharge. Completely discharging before recharge will ultimately kill them. Use the 1815X till almost dead and then charge it. It is also recommended Lith-Ion batteries not be stored fully charged i.e. charge the 1815X fully, drive a couple bolts or screws, remove the battery unit and then put it away. Do not leave battery unit plugged into the tool when you put the tool away. This will discharge and kill the battery unit.

There are non-Hitachi substitute batteries now on the market. I'm guessing the same precautions apply but I don't own one of the replacements so I don't truly know.

The actual batteries in the Hitachi BSL 1815X are Sanyo UR18650SAX lithium ion batteries. Lithium Ion cells aren't all that easy to get commercially because of handling & safety requirements. Not certain if you can take apart the 1815X and swap out the bad Sanyo cells.

the red light turns on automatically after 120 hrs of running to remind us for cleaning the filters. once you cleaned the filters and inserted back , then just keep ac in stand by mode, open the remote panel and press the button on extreme right bottom of the remote ( see carefully in the remote, there is very light image of the filter is made along with the button). red light will go off. no need to press the reset button.... enjoy

Simple question, is there something inside of the blade and the blade guard blocking its use? Sometimes a piece of wood or plastic lodges itself in between and is hard to see.

https://www.manualslib.com/products/Hitachi-Uc-18yksl-3659810.html

try the master reset in the menu, or unplug it and let it sit for about fifteen minutes

It is a disk error! Change the disk you are using, probably you are trying to use an RW disk! Better +/-R.

Good concept.Thanks for sharing

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/ Faults & possible causes to LCD screen are given with illustrations. You can get an idea about the fault to an extent. View the site by desktop or web view on mobile devices to see the "search box". Type in the brand name of your set in search box; to get gathered the related posts. Screen-shots to defective LCD panels are given. You can see and compare to that to your TVs', and can make sure about the fault to an extent.

First make sure that the current Source or Input is set to TV. This is usually the only reason for the error message you see. To select the source, look for a Source or Input button on the original remote. If you have an universal remote with a button with the Source/Input label, you may need to try alternative codes to make the button work. (Power and channel controls will often match across multiple codes for the TV manufacturer.) Alternatively, check if there is a Source/Input button on the TV or a section of the menu system with the function. Once you set this source, try again. Note: there was a period when manufacturers sold some TVs without tuners. They were labeled HD-ready sets. These can't do a channel scan and do not have an RF antenna jack on the set. I hope this helps. Please add a comment with the model number of your Hitachi TV for more information on setting the source on your set. Cindy Wells

Under Audio or Audio Settings on the on-screen menu, TV Speakers is set to On. All of the cables physically connected to the TV and the input devices are secure. Switch to a different input device and verify there is sound from the TV speakers (for example, a DVD player or a gaming console). https://www.ifixit.com/Answers/View/310570/The+sound+on+my+TV+stopped+working.

The OEM chuck for that is about 45 dollars. There are no substitutes offered.

look on the back of the television and the DVD player, there should be a SCART socket and/or red, white and yellow AV sockets, either use a SCART lead and connect it to the SCART on the DVD player and the TV.Or use an AV lead with 3 auxiliary shape connectors and match the colour of each connector with the female sockets on both the TV and the DVD player instead of using the other component connections.

Hey! As far as I know, vob is the format of videos on the DVD-R discs.
I think you need a conversion tool and this DVD Converter Ultimate will be of help to you. This DVD Converter can help you convert various video format (including vob format )to any video format, rip dvds to video and burn video to dvds for playing on DVD players. You can have a free try of it. Hope that helps.

The timer lamp (orange) flashes. The timer lamp flashes to indicate that the Streamer unit needs cleaning. After cleaning the Streamer unit, reset the lamp. (1) After cleaning, connect the power cord to AC outlet or turn on the circuit breaker. https://www.daikin.com/products/ac/services/troubleshooting/

Try Ritchie street near the Bata Shoe Shop on Anna Salai road after the LIC stop.
If you have a catalog or picture of the TV go with it and show it around some of the TV shops they might show interest or arrange a buyer for you.Ask some of the many repair shops too - they are on the look out for spares.

hitachi's site or online search

That means that the indoor unit is not communicating with the outdoor unit. Check all the cables between the two units, look for broken wires, corrosion and loose fittings

check and test cut out may be faulty or failing

Troubleshoot: https://www.ifixit.com/Wiki/Hitachi_HB-B102_Automatic_Home_Bakery_II_Troubleshooting https://www.scribd.com/doc/20815448/18122724-Hitachi-Home-Bakery-Model-HBD102-Instruction-Manual-Recipes-HBD102-1