Hisense Televison & Video - Page 9 - Recent Questions, Troubleshooting & Support

go see the dealer where you got it we do not have any here

The most main common reason for a TV to be showing a blue screen with no picture is because the source device has not been set to the correct mode.If you are using a VCR that is powered on but is not playing a tape and is not tuned to on to a receivable channel a blue screen will be showing up on the TV"s screen.

consult your local dealer

usually a back light problem call a repair service

check input or source and check power settings see if programmed to turn off and on

Depending on where you live, service to teletext finished between the 1990s and early 2000s https://en.wikipedia.org/wiki/Teletext ..

Hello Ginnie, it may be that your remote control has the VOL-locked button and produces the fault, to test the batteries to the remote control and check if it continues to do so. Another option may be that the VOL- control, on the TV, is locked or has some internal dirt and generates a false contact that could cause the failure Check these points to see if you have problem solution If not consult a specialized technical service I hope I can solve the problem Greetings Franco Dosil Hola Ginnie, puede ser que su control remoto, tenga el bot?n de VOL- trabado y produzca la falla, para probar saque las pilas al control remoto y compruebe si lo sigue haciendo Otra opci?n puede ser que el control de VOL- , en el televisor, se encuentre trabado o tenga alguna suciedad interna y genere como un falso contacto que pueda provocar la falla Compruebe estos puntos a ver si tiene soluci?n del problema Sino consulte a un servicio t?cnico especializado Espero pueda resolver el problema Saludos Franco Dosil

To make a reset, you have to enter its service mode. To enter the service mode, a remote control is necessary. If you haven't a remote control, just buy one. then get into the service mode, and make a reset. If you wish to get some details; check the site linked here. Pull up older posts. https://electronicshelponline.blogspot.com/ https://elektrotricks.blogspot.com/ If you wish to buy its original remote control, contact the authorized service centre, or authorized dealer to your device brand. They can either give you a genuine remote control to your device, or can direct you, from where can you purchase a suitable one. To select a proper universal remote control, you should know about the number of digits to its set-up codes. There are 3 digit, 4 digit, 5 digit, 2 digit and even single digit codes, to some brand devices. After confirming this, check the sites linked here. Both the sites have set-up code list and set-up procedure to many popular brand remote controls. Check which brand remote control has set-up code/s to your device brand, and buy that one according to availability? Brand name of the remote control isn't a matter, but it should have set-up codes in its code list, to the device brand you have. Please note: Every new universal remote control will have set-up code list, and set-up procedure along with its pack. Never accept a remote control, that hasn't both of this. For more details about the set-up codes, visit the site http://electrohelponline.blogspot.com/ Check these sites too. http://remotesearch.blogspot.com/ https://elektrotricks.blogspot.com/ Universal remote controls are available at most of the electronic spare part selling shops; as well as online shops.

Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Pull up older posts or search the site by type in the brand name of your set, at its search box at the right column.. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/ https://elektrotricks.blogspot.com/

Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/

could be a bad video board or a the audio only setting got enabled but id need the model number to help you out some more

If the blue light stays on do yo get any sound?

Dont rush into changing boards. In many of those sets, the issue is back light LED strips that fail and the power board shuts down.

Probably power supply failure

possible bad power board

Why can't you just buy the remote control?

The Hisense EN3G39 is the remote control for the 55N8700UW, 65N8700UWG, and other TVs. I have never seen an option for removing the standby mode from any TV without a change to the firmware. The TV will always return to the standby mode when power is returned. The type of firmware change that you want will not be available from the TV manufacturer. The smart plug is great for reducing your power bill when you aren't watching TV. It won't avoid the turn on step. I wish that I had better news for you. Cindy Wells (I wouldn't recommend trusting a third-party firmware if one exists or was created for your TV. That would void any warranty and could cause problems with the TV.)

Probably a back light LED failure.

1. Open internal fuse2. Power supply failurePlease check this link: https://www.google.com/search?bih=625&biw=1366&hl=en&ei=muLyX5yZKOraz7sP2_2moAo&q=How+to+fix+Hisense+b50h5g+won%27t+power+up+standby+light+turns+off+screen+blank&oq=How+to+fix+Hisense+b50h5g+won%27t+power+up+standby+light+turns+off+screen+blank&gs_lcp=CgZwc3ktYWIQAzoICAAQyQMQkQI6BQgAEJECOgIIAFCisylY5LspYMrCKWgAcAF4AIABeYgB4AGSAQMwLjKYAQCgAQGgAQKqAQdnd3Mtd2l6wAEB&sclient=psy-ab&ved=0ahUKEwicztGR_oHuAhVq7XMBHdu-CaQQ4dUDCA0&uact=5Hope this will help.

bad horizonal hold board