Ah, 'MD Start' is the NAME of the maker of a Medical washer, nothing to do with Metal Detecting, one of my other fields of expertise!
Contact them direct, as this is not a consumer appliance, and they are based in Paris and we are in North America.
https://www.google.com/search?q=MD+start
The solenoid in the lock has probably failed.
..
Error code POR on a Defy top loader washing machine typically indicates a problem with the machine's power supply or control board. Here are some steps you can take to resolve this error:
Check the Power Supply:
Make sure the washing machine is properly plugged into a working electrical outlet.
Check if there's a power outage in your area. If there is, you may need to wait for the power to be restored.
Ensure the power cord is not damaged or frayed.
Reset the Washing Machine:
Unplug the washing machine from the electrical outlet for a few minutes.
Plug it back in.
Try turning the machine on again and see if the error code clears.
Check the Control Panel:
Examine the control panel for any visible issues such as loose or disconnected wires or damaged buttons.
Press and hold the "Cancel" or "Pause" button for a few seconds to reset the control board.
Circuit Breaker or Fuse:
Check your home's circuit breaker or fuse box to ensure that the circuit providing power to the washing machine hasn't tripped or blown a fuse. Reset the circuit breaker or replace the fuse if necessary.
Voltage Fluctuations:
Voltage fluctuations or surges can sometimes trigger error codes. Consider using a voltage stabilizer or surge protector to regulate the power supply to the washing machine.
Consult the Manual:
Refer to the user manual or owner's guide that came with your Defy washing machine. It may provide specific troubleshooting steps for error code POR.
Contact Customer Support:
If the error code persists after checking the power supply and attempting a reset, it's recommended to contact Defy's customer support or a qualified appliance technician for further assistance. They can diagnose and repair any internal issues with the washing machine.
Keep in mind that error codes can vary by model and manufacturer, so it's important to consult your washing machine's specific manual for guidance on error codes and troubleshooting. If you're not comfortable performing troubleshooting or repairs on your own, it's best to seek professional assistance to avoid causing further damage to the appliance.
This is a clutch problem.
Or the agitator just need tightening down. Remove the stuff from the top and down inside you will see a deep seated bolt. Tighten it.
'make model (what it is)' in all questions please.
Then you can Google
make model REMOVE agitator
And then do the reverse!
..
To solve the E2 error on your Scanfrost washing machine, you can try the following steps:
1. Check the water supply: Ensure that the water supply is properly connected and turned on. Make sure there is sufficient water pressure for the machine to operate.
2. Clean the filter: Locate the filter on your washing machine and remove any debris or lint that may have accumulated. A clogged filter can cause the E2 error.
3. Check the drain hose: Ensure that the drain hose is not clogged or kinked. Straighten any kinks and remove any blockages if necessary.
4. Check the drain pump: The E2 error can also be caused by a malfunctioning drain pump. Inspect the pump for any blockages or damage. If needed, clean or replace the pump.
5. Reset the machine: Turn off the washing machine and unplug it from the power source. Wait for a few minutes, then plug it back in and turn it on again. This can sometimes reset the error code.
6. Contact customer support: If none of the above steps work, it's best to reach out to Scanfrost customer support for further assistance. They may be able to provide specific troubleshooting steps or arrange for repairs if needed.
Remember to consult your washing machine's user manual for any specific instructions or warnings before attempting any troubleshooting steps.
There is ZERO context to this question except that it might be a washing machine because that is the category you are in.
Filter access panel?
All questions on Fixya need 'make model (what it is)', first 3 words.
Google
make model manual
or
make model clean filter
https://www.google.com/search?q=washing+machine++clean+filter
..
All questions need 'make model (what it is)' and you only have 1/3.
E3 is water too high or too low, or hot water related not hot enough or vibration depending on maker.
Error message E3 in integrated compact dishwasher indicates too much inlet water and/or a leak.
Oct 7, 2019
The warranty coverage for bearings or any other specific components depends on the manufacturer and the terms of the warranty provided. Warranties can vary between different products and brands. It's essential to check the warranty documentation that came with the product or contact the manufacturer or the place of purchase to get accurate information about the coverage.
Typically, warranties cover defects in materials or workmanship for a specified period from the date of purchase. However, normal wear and tear or damage caused by misuse may not be covered. Be sure to review the warranty terms and conditions to understand what is included and excluded from the coverage. If you have a specific product in mind, you can check the manufacturer's website or contact their customer support for detailed warranty information.
