GMC Logo

GMC Answered Questions & Fixed Issues

Do you work here? Claim your company

  • 709 Products
  • 189K Answers

It could be a leaking fuel injector or a bad fuel pressure regulator. Do this plug the fuel return line then turn the switch on then off, if the pressure holds replace the fuel pressure regulator. If the pressure bleeds down remove the fuel rail with the injectors still attached and see which ones leak. I hope this helps. Take care.

GMC Sonoma Cars... | Answered 6 hours ago | 18 views

What do you mean it is showing connector 1 light on. What or where is this light?

GMC Cars &... | Answered Yesterday | 17 views

it means there is a problem with the air suspension.

2003 GMC Yukon... | Answered 2 days ago | 714 views

Your anti-theft system kicked in for some reason. If you shut it off, the engine will turn over but will not start. A Chevy or GMC dealership is usually required to reset the system, but you'll have to bring it to them. Dealer + Towing = BIG $$$$. A less expensive option would be a mobile mechanic (call them first) or a licenced locksmith. Either way you'll need to show ID and proof of ownership.

2002 GMC Envoy | Answered 2 days ago | 25 views

Everything you mention is in the same door. Look for a connector between the body and the actuators in the door. This may be accessible or just inside the door itself, past a rubber grommet. Pull the connector apart and inspect it. Spray with silicon or WD40 and reassemble.

GMC Acadia Cars... | Answered on Apr 21, 2019 | 25 views

Hi, from your description, the problem could lie within the fuel system. Unless it's been replaced recently, the in-line fuel filter could be clogged (after 15 years, it's overdue if it hasn't been replaced).

GMC Cars &... | Answered on Apr 19, 2019 | 23 views

Most gms that won't back up have a split cage internally.Good thing is it is a reasonably easy fix.

GMC Cars &... | Answered on Apr 18, 2019 | 24 views

2nd try.

  • Fuel pressure is good.
  • Test lamp show VCM is commanding injectors to open.

So your thought is the common side of the injectors are not powered. I believe this is the correct schematic for a '97 suburban.
There is the ECM1 fuse but hard to believe that fuse is blown, check it anyway.


GMC Cars &... | Answered 3 days ago | 148 views

You will need to contact your local GM dealer service department.

GMC Cars &... | Answered on Apr 18, 2019 | 21 views

Hi, Any other issues w/the truck? Does the speedometer work ALL the time? Some of these use engine vacuum to control the Cruise. Check under the hood -around the engine - and verify the vacuum lines are all securely attached. BE CAREFUL - do this w/the engine off and ENSURE you note where all the hoses are connected. There may be a lot and easy to get them confused.

GMC Cars &... | Answered on Apr 17, 2019 | 20 views

How do you know they need to be replaced ? The switches incorporate a electronic module . Driver door module .
Power Window System Components
The power window system consists of the following components:
• Driver Door Module (DDM)
• Passenger Door Module (PDM)
• Body Control Module (BCM)
• RR power window switch
• Window up and window down relays in each of the rear passenger window switches
• Window lockout switch
• Reversible power window motors in each of the doors (circuit breaker protected)
• LT DOOR CB 25A (System power for left windows)
• RT DOOR CB 25A (System power for right windows)

Power Window System Controls
The power window system will operate anytime the Retained Accessory Power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The DDM contains four power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the two front windows have three positions UP, Down and Express Down, while the switches for the rear windows have only two positions, UP and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a Class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has two positions Up and Down. Each of these switch positions is a direct input to the PDM.
The two rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a Class 2 message from the DDM, can control the set of relays which will activate the rear window motors.

The door locks operate the same way .

Door Lock System Components
The power door lock system consists of the following components:
• The driver door module (DDM)
• The passenger door module (PDM)
• The body control module (BCM)
• The driver information center (DIC)
• The rear door lock switch
• The door lock relay
• The door unlock relay
• The liftgate lock relay--utility vehicles with liftgate only
• The reversible door lock actuators in each of the doors and liftgate
• LOCKS 20A fuse (rear lock/unlock relay supply voltage)
• ECC 10A fuse (liftgate lock relay supply voltage)

What's not working ? Windows , power locks ?
Hooking up a professional type scan tool ,not a code reader . Code reader can not read codes in the BCM or door modules . Do you know what a DTC is ? diagnostic trouble code >All these can set for door electronic problems .
DTC B1023
DTC B1544, B1600, or B1605
DTC B1580, B1590, B1610, or B1620
DTC B1640 or B1645
DTC B1722
DTC B3808
DTC B3809
DTC B3819
DTC B3820
DTC B3821
DTC B3822
DTC B3823
DTC B3824

GMC Yukon Cars &... | Answered on Apr 17, 2019 | 26 views

your on the right track! your blend door is broken or your blend door actuator is broken.

2011 GMC Acadia | Answered on Apr 17, 2019 | 21 views

You usually will not find them for free, but Mitchel, Motor, and Chilton all have wiring diagrams included in their service manuals.

GMC Cars &... | Answered on Apr 17, 2019 | 29 views

You will get the wiring diagram from the given link

GMC Cars &... | Answered on Apr 17, 2019 | 25 views

A bad master switch can do that, remove the switch from the drivers door and check for power and ground at the switch if OK replace the switch. I hope this helps. Take care.

GMC Cars &... | Answered on Apr 16, 2019 | 16 views

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Popular Products

2004 GMC Envoy
2004 GMC Envoy

2,171 Questions

2000 GMC Jimmy
2000 GMC Jimmy

1,327 Questions

2002 GMC Envoy
2002 GMC Envoy

1,362 Questions

2003 GMC Envoy
2003 GMC Envoy

1,326 Questions

1997 GMC Jimmy
1997 GMC Jimmy

1,099 Questions

Top GMC Experts


Level 3 Expert

84565 Answers

Brad Brown

Level 3 Expert

18031 Answers


Level 3 Expert

2360 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides