GMC Electrical Supplies - Page 5 - Popular Questions, Answers, Tips & Manuals
I have a kubota av6500 generator runs great but the output voltage at the 120volt receptacle is 163 volts and at the 120 voltage 20amp plug is 38volts what could be the problem thanks
There could be several reasons why the output voltage of your generator is not within the normal range. Here are a few things you can check:
- Make sure the generator is properly grounded.
- Check the voltage regulator. It could be malfunctioning and causing the high voltage output.
- Check for loose or damaged wiring. Any issues with the wiring could cause the voltage to be incorrect.
- Check the engine speed. If the engine speed is too high, it could cause the voltage to be higher than normal.
- Check the load on the generator. If the load is too low, it could cause the voltage to be higher than normal.
If you are unable to identify and fix the problem, it is recommended to have a professional technician diagnose and repair the generator.
12/14/2022 3:52:56 PM •
Electrical...
•
75 views • 0 helpful votes
Carrier comfort pro 6100 apu
If the Carrier Comfort Pro 6100 APU is not producing AC voltage, it will shut off as it is designed to do so to protect the system. This is because the APU needs to have a stable voltage output to run properly, and if there is no voltage, the system will shut down.
Regarding the circuit breakers, it's possible that they may be faulty and need to be replaced. You can test the breakers with a multimeter to determine if they are functioning properly. If they are not, you will need to replace them.
However, there could be other issues causing the lack of voltage from the generator. It's possible that the generator itself is faulty or that there is an issue with the voltage regulator. A professional technician with experience working on APUs would be best suited to diagnose and repair the issue.
10/27/2022 12:08:15 AM •
Electrical...
•
241 views • 0 helpful votes
Power switch discontinued
If you received the single pole switch as an alternative from a Miller dealer/service then it should have came with instructions.
Likely it can be done but the unit will no longer have a complete de-energized state, just merely open circuit which means it will function electrically but not necessarily meet safety standards which may or may not be a problem in your service environment.
I'd suggest a DPST such as;
https://www.amazon.com/Miller-116830-Switch-Rocker-250Vac/dp/B004HEDK1G
However, it may or may not be the same physical dimensions. Contact seller.
12/31/2022 5:11:18 AM •
Electrical...
•
31 views • 0 helpful votes
Where can I get a replacement Ann YIH AM-06 motor?
See if either of these are anywhere close... you may need to be creative with mounting or shaft adaption but both are ccw 6rpm 120vac.https://www.amazon.com/uxcell-Synchronous-100-127V-5-6RPM-50-60Hz/dp/B07Y6LQ9S7https://www.ebay.com/itm/284538092633https://www.harfington.com/products/p-1030989?currency=USD&variant=42245771526393&utm_medium=cpc&utm_source=google&utm_campaign=Google%20Shopping&utm_source=google&utm_medium=cpc&utm_campaign=1008-pmax-us-powerele8&utm_term=1008-pmax-us-powerele8&utm_content=ywh&gclid=Cj0KCQjw4omaBhDqARIsADXULuXL5kHwCBY5CH_b_K3E3orB4olt3JqZjfMx9Mp8mnp4ysJ-plzqOGoaAshNEALw_wcB
10/9/2022 8:48:18 PM •
Electrical...
•
172 views • 0 helpful votes
Can this controller be replaced with a controller thats not nema 4
Whether or not a NEMA 4 controller can be replaced with a controller that is not NEMA 4 depends on the specific application. NEMA 4 controllers are designed to withstand water and dust ingress, so they are often used in outdoor or harsh environments. If the controller is being used in an environment where it is exposed to water or dust, then it is important to replace it with a NEMA 4 controller.
Overall, it is important to consult with a qualified electrician before replacing a NEMA 4 controller with a controller that is not NEMA 4. The electrician can assess the specific application and recommend the best controller for the job.
If you want to look for a controller, you can visit: https://www.chipsmall.com/bigcategory/industrial-automation-and-controls.html to search for the controller you want.
10/10/2022 3:32:24 PM •
Electrical...
•
95 views • 0 helpful votes
Not finding what you are looking for?