General Popular Questions, Answers, Tips & Manuals

Ideas in the link, but this is a commercial washing machine. https://www.google.com/search?q=super+general+washing+machine+E53+code ..

Turn off the breaker or remove the outside breaker contact link for at least 2 hours. This will do a full software reset. When you turn it back on, wait 10 minutes for the self test procedure to complete. If that doesn't fix it, look for diagnostic flash codes and look them up online. Or call for service. https://www.google.com/search?q=super+general+split+unit+air+conditioner+flash+codes+list ..

We don't have these strange machines in north America. If it is new it is under warranty and needs a claim. It sounds like the main board has failed, or the timer. Not finding that model https://www.google.com/search?q=Super+General+Washing+Machine+SGW10225 ..

EF indicates a water inlet temperature sensor error. EP indicates a discharge pipe temperature sensor failure alarm. EU indicates an air side heat exchanger refrigerant total outlet temperature sensor Tz/7 error. or What does EF mean on mini split? Eb - The Communication abnormal of Main PCB and Display board(IDU failure) EE - ODU EEPROM failure. EF - ODU DC fan motor failure. I don't think we don't have Super General in North America. Dubai, UAE, Oman company? ..

Question edited for clarity. E3 is a generic 'Off Balance' code If you receive an E3 Error code, your washer may be unbalanced. This could be caused by the washer being too tightly packed, or clothing not distributed evenly. This will usually occur during the spin cycle. Stop the spin cycle.

E3 - Error Code - Stacked Laundry Center - Whirlpool Canada

F8 is taking too long to fill. Check the filter screens on the rear hoses. The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water. If the washer has an F8 E1 error or LO FL error, the door may be locked, and the control may be unresponsive. Aug 21, 2023

F8 E1 or LF or LO FL Error Code in Display - Washers - Amana

..

An "F9" error code on your air conditioner typically indicates a problem with the indoor unit's fan motor. This error code can vary depending on the make and model of your air conditioner, so I recommend checking your air conditioner's user manual or consulting the manufacturer's website for specific information related to your unit. In most cases, the F9 error code is associated with a malfunctioning fan motor, which may be caused by issues such as a faulty motor, damaged wiring, or a problem with the control board. Here are some general steps to help diagnose and address the issue:

1. Turn Off the AC: First, turn off the air conditioner to prevent any further damage or electrical issues.
2. Check for Obstructions: Ensure that there are no obstructions blocking the indoor unit's fan blades.
3. Check the Wiring: Inspect the wiring and connections to the fan motor for any loose or damaged wires. If you find any issues, you may need to replace or repair the wiring.
4. Reset the Unit: Some air conditioners have a reset button or function. Try resetting the unit to see if the error code clears.
5. Call a Professional: If the error code persists, it's best to contact a qualified HVAC technician or the manufacturer's customer support for assistance. They can diagnose and repair the problem, which may involve replacing the fan motor or control board, if necessary.

Send it back under warranty and get a refund. Logitech and Microsoft are the brand leaders in Mice and are fully tested.

If the green light is blinking on the front panel of a ceiling cassette air-conditioner unit, the basin is about to overflow. You need to clean it ASAP. If the timer or operation light is blinking on a wall-mounted air-conditioner, there may be abnormality detected, please contact your service team.

FAQ-Knowledge bank-General Air-Conditioner

Question edited for clarity. Question moved from Cars and Trucks, because it isn't. help in the link, plus access to the maker. https://www.google.com/search?q=gp+t+series+47+ts1321+schematic+diagram ..

The error code E12 on a Super General washing machine indicates a drainage issue. This could be caused by a few different things:

1. Clogged drain hose: The drain hose that carries the water from the washing machine to the drain may be clogged. Check the drain hose to make sure that it is not blocked by debris.
2. Drain pump: The drain pump is responsible for pumping the water out of the washing machine. If the pump is clogged or damaged, it will not be able to pump the water out and the machine will display an E12 error.
3. Drain filter: The drain filter is located in the drain pump and is responsible for trapping debris that may clog the drain hose. Check the drain filter to make sure it's not clogged.
4. Control board: The control board manages the washing machine's functions and if it's faulty it can cause the drain pump to run continuously and display the E12 error.

It's recommended to first check the drain hose, drain pump, and drain filter to see if they are the cause of the issue. If these are all clear, the problem may be with the control board, which will require professional repair. Please be careful when checking the drain pump and filter, as the water may be hot if the machine is in the middle of a cycle.

did you get the 4 rubber washers that go in the hose ends?

Question also edited for clarity. This one was worse! You need a manual, and as stated, you need the model number to find it. The tension dial should be set are the middle. If it goes 1 - 10, set it at 5. If the thread is laying at the bottom, you increase the tension to say 6, or 7. If it is bunching at the top, your turn it down to 4. Your big dial will be either stitch length or the stitch type, plain, zig zag, buttonhole, tacking stitch, blind stitch etc. https://www.google.com/search?q=craft+mate+sewing+machine& This is the best video that explains tension

If the water level in your Super General SGW720N top load automatic washing machine is not stopping and is overflowing, there could be a few possible causes. Here are a few steps you can try to troubleshoot and fix the problem:

1. Check the water supply hoses: Make sure the water supply hoses are properly connected and there are no visible signs of damage or leaks.
2. Check the water level sensor: The water level sensor is responsible for controlling the water level in the machine. If it is not functioning correctly, it could cause the water level to continue rising. You may need to have the sensor cleaned or replaced by a professional.
3. Check the water inlet valve: The water inlet valve controls the flow of water into the machine. If it is not functioning properly, it could cause the water level to continue rising. You may need to have the valve cleaned or replaced by a professional.
4. Check the control board: If the problem is not with the water supply hoses, water level sensor, or water inlet valve, it is possible that there is an issue with the control board. You may need to have the control board inspected or replaced by a professional.

If you are unable to resolve the problem on your own, it is recommended to contact a qualified service technician or the manufacturer for further assistance. It is important to follow the manufacturer's instructions when attempting to repair or troubleshoot your washing machine to avoid causing further damage or injury.

If the bottom heating element in your General Electric oven is not working, there could be a few different causes. The first thing to check is the element itself. You can do this by turning off the power to the oven, removing the racks, and then visually inspecting the element for any signs of damage or discoloration. If the element looks damaged or worn, it may need to be replaced. If the element appears to be in good condition, the issue may be with the oven's electrical system. In this case, you may want to consult a professional electrician or appliance repair technician for further assistance. They can perform an electrical check to determine if there are any issues with the wiring or electrical connections. Regarding the fuse, most ovens have a thermal fuse that is designed to protect the oven from overheating. This fuse is usually located on the back of the oven and can be checked with a multimeter. However, if the fuse is blown, it typically affects both the top and bottom elements, not just one. So, it is unlikely that a blown fuse is the cause of the bottom element not working. In summary, if the bottom element is not working in your General Electric oven, start by checking the element itself for damage. If the element appears to be in good condition, it may be a more complicated electrical issue that requires the help of a professional.

Question edited for clarity. How do I fix P2 error in AC? If the P2 or FL error code is displaying on the air conditioner, remove the drain port cap and tilt the air conditioner to the back so the water runs out of the drain outlet. If no water is draining out when the air conditioner is tilted to the back, the unit will require a repair service. Dec 11, 2018 More here and videos https://www.google.com/search?q=super+general+inverter+ac+p2+P2+error+code ..

Error code E3 on a Super General air conditioner model SGSi188-i5 indicates a communication error between the indoor and outdoor units. This could be caused by a faulty control board or a wiring issue. You may try resetting the air conditioner by turning off the power supply for a few minutes and then turning it back on to see if the error code disappears. If the error code persists, it is recommended to contact a professional technician to diagnose and fix the issue.

Question edited for a bit of clarity. This doesn't appear to be a General Electric (GE) machine and looks to be an Arabian machine. We are in North America. This link might work better for you in your county. https://www.google.com/search?q=super+general+automatic+washing+sgw721+e+error+code ..

Hi, Please make sure that the customer is calling the correct number that you think that they're calling. Then, call this number yourself and leave a message before going to check the message again. If you can't find your message, please call the business' phone company and ask them if there are multiple mailboxes linked to your business phone number. If so, they can provide access to the other mailbox for you. Thank you.

You can use seal material and make your own. Or you can order by size. https://www.google.com/search?q=General+Freezer+GC12L+Gasket ..