GE Recent Questions, Troubleshooting Help & Support

Question edited for clarity 'MAKE model (WHAT IT IS)'. You posted to Televisions, moved to GE Washing Machine. It may be the lid lock, test it with your digital multimeter. Look for loose or damaged connections. https://www.google.com/search?q=GE+Gtw330ask0ww+not+running ..

check under agitator possible worn cogs

check voltage to pump if ok bad pump also check drain hose

There could be several reasons why the internal lights in a vehicle may not be working while the panel lights are functioning. Here are a few possible explanations:

1. Blown fuse: Check the fuse box to see if the fuse for the interior lights has blown. If it has, replace it with a new one of the same rating.

2. Faulty light switch: The switch that controls the interior lights may be faulty or worn out. Try toggling the switch on and off to see if it makes any difference. If not, consider replacing the switch.

3. Loose or corroded wiring: Inspect the wiring connections for the interior lights. Loose or corroded connections can disrupt the electrical flow and prevent the lights from working. Tighten any loose connections or clean off any corrosion.

4. Burnt-out bulbs: If all the interior lights are not working, it's possible that multiple bulbs have burnt out at the same time. Check the bulbs and replace any that are no longer functional.

5. Dimmer switch settings: Some vehicles have a dimmer switch that controls the brightness of the interior lights. Make sure the dimmer switch is not turned all the way down or set to a very low level.

If none of these solutions resolve the issue, it may be best to consult a professional mechanic or electrician to diagnose and repair the problem.

Check the water level sensor.

Just remove the drain hose from the drain upstand pipe and lower it to the floor. It will empty the pump or water.You can also drop a pint of car anti freeze into the machine just to be sure if you wish.

https://www.google.com/search?q=GE+326B1036P001+touch+pad+buttons ..

You likely have a water leak spraying onto electrics, or the water inlet valve is shorting out.

https://products.geappliances.com/appliance/gea-support-search-content?contentId=22067 https://www.youtube.com/watch?v=LOYwkydARlY

That issue sounds like it it likely to be the control board, or maybe a bad connection to it or a dry joint. https://www.fixya.com/support/r29874712-repairing_microwave_ovens ..

You can't modify gas appliances.

Remove the bottom impeller and clean out the water proof grease that has come out of the seal and drive shaft.

My advice is get rid of it. Or test every joint with washing up liquid and water in a spray bottle. This is what a gas explosion can do to your house. Our windows rattled 2 km away! https://www.google.com/search?q=mississauga+Hickory+Drive+gas+explosion ..

Some help in the link. None are free https://www.google.com/search?q=repair+manual+for+a+GE+electric+range+%23+R+B526+H3BB ..

Refer to page 40 to 44 (Troubleshooting Tips) of manual L0707187 (searspartsdirect.com)

When it hit the floor you have probably knocked something loose inside the motor itself. You will need to check it spins freely by hand and check the carbon brushes for the armature. You may also need to strip the motor down to check all the wiring connections inside the motor.

I have an early 1970s GE, and we keep saying when it breaks down, we will replace it, but apart from replacing elements, it just goes on and on. Unfortunately, neither of your numbers give results. There should be a plate near the power lead that has the details and some have a parts manual and wiring diagram in the rear of the console if it has one. https://www.google.com/search?q=GE+82212+cooktop https://www.google.com/search?q=GE+YT123887L+cooktop ..

Most modern appliances like cookers and washing machines have the control panels and displays are fitted from behind the front panel, inside the machine. You will be better off getting a professional repairer to do it for you. *Remember* this is a Gas appliance that you're working on so BE CAREFUL. You might have to remove several other panels to get to the touch pad so if your going to do it yourself turn OFF the main gas supply first then make notes and take photos as you go.

it should lift out once you it tilted. page 5 this not your exact model, but they are mounted the same way https://documents.designerappliances.com/Installation-Instructions-JXA019K.pdf