GE Ovens - Page 2 - Recent Questions, Troubleshooting & Support
GE Trivection JT930SOH1 Oven, touch screen not lighting up
The thermal fuse in your GE Trivection JT930SOH1 oven is likely located behind the touch screen control panel. In order to access the thermal fuse, you will likely need to remove the control panel.
Before attempting to access or repair the thermal fuse, it's important to ensure that the oven is unplugged and that you have taken proper safety precautions, such as wearing gloves and eye protection.
Instructions to access the thermal fuse may vary depending on the specific model of your oven, so it's recommended to check the owner's manual for your oven or contact GE for instructions.
However, in general, you may be able to access the thermal fuse by first removing the control knobs and screws that secure the control panel in place. Then, you'll likely be able to lift the control panel off of the oven to access the thermal fuse.
It's important to note that the thermal fuse is a safety device, and it's designed to blow if the oven overheats. If the thermal fuse is blown, it will need to be replaced. If the fuse is not blown and the touch screen is still not lighting up, it could be a problem with the touch screen itself or a problem with the wiring or other electrical components of the oven.
It's recommended to contact a certified technician to diagnose and fix the problem.
1/14/2023 5:15:55 PM •
GE Ovens
•
Answered
on Jan 14, 2023
GE JKP26 Double Oven. The broiler trips circuit breaker.
Question edited for clarity.
One of Broil elements have failed. Often you can visually see the damage, or you can test with a multimeter with the power turned off. Try for continuity. The failed one will be shorting to earth. The other possibility is that an end contact has melted through and is touching the case.
1/4/2023 3:00:18 AM •
GE Ovens
•
Answered
on Jan 04, 2023
GE Profile PT916SM1SS will not heat up past 290
Hi,
please check that the oven isn't leaking heat into another area. Or maybe your settings need some calibration or the temperature sensor for the oven is off by 60 degrees. If this is the case, changing the temperature setting to 410 should bring the internal temperature to 350 degrees. Please try this.
Thank you.
11/12/2022 5:59:38 AM •
GE Ovens
•
Answered
on Nov 12, 2022
Got error code F9 while oven cleaning in process.
An F9 error code on a General Electric (GE) oven indicates that the oven's electronic control system has detected a problem with the automatic door lock.
The automatic door lock mechanism prevents the oven door from being opened when the oven is set for "Clean" mode.
The malfunction may be a jammed door lock mechanism, a pinched or broken wire, a faulty lock switch or a fault in the control board itself.
9 out of 10 times the lock switch has failed.
STEP # 1 -
Disconnect power to the oven!!
Step 2
Open the oven door. Remove three screws from underneath the oven's control panel. Lift the control panel straight up to disengage the mounting pins on the top corners of the panel, then tip the panel toward you.
Step 3
Inspect the door lock mechanism. The mechanism is in the lower left area of the space behind the control panel. Rotate the cam on the door lock mechanism to be certain it moves without binding. Replace the mechanism if its mechanical parts do not function properly.
Step 4
Inspect the wires that connect the door lock mechanism to the control panel. Check for pinched or broken wires. Check for wires with frayed insulation. Repair wires as needed if defects are present.
Step 5
Locate the six-pin connector on the door lock motor on the right end of the door lock mechanism.
Step 6
Rotate the cam on the door lock mechanism to the unlocked position. Test the resistance between Pin 3 and Pin 1 of the door lock connector with the ohmmeter. The resistance should be 0. Replace Lock Switch 2 of the door lock mechanism if the resistance reads other than 0.
Step 7
Rotate the cam on the door lock mechanism to the locked position. Test the resistance between Pin 3 and Pin 2 of the door lock connector with the ohmmeter. The resistance should be 0. Replace Lock Switch 1 of the door lock mechanism if the resistance reads other than 0.
Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
Jrp24bow3bb electric double oven control panel.
Hi rhonm,
You should have found a connection diagram in the top of the oven. If you didn't, call GE at the following number and they will send you one. 1-800-626-2005
It would be very difficult for any one to make a recommendation without seeing the oven or part. Are there one or two gray wires? My first guess is that they sent you the wrong part. See photo for typical double oven ERC.
Regards,
Powerman
6/15/2022 7:48:32 PM •
GE JRP24...
•
Answered
on Jun 15, 2022
Not finding what you are looking for?