Frigidaire Popular Questions, Answers, Tips & Manuals

There are a few possible reasons why an Electrolux window AC unit may be blowing cold air when set to heat mode. Here are a few things you can try to fix the problem:

1. Check the thermostat settings: Make sure that the thermostat is set to "heat" mode and that the temperature is set higher than the current room temperature.
2. Clean the air filter: A dirty air filter can restrict airflow and prevent the unit from heating properly. Clean or replace the filter according to the manufacturer's instructions.
3. Check the air ducts: Make sure that all of the air ducts are properly connected and that there are no leaks or blockages.
4. Check the compressor: If the compressor is not running, the unit will not heat. Make sure that the compressor is running and that the compressor's fan is functioning properly.
5. Inspect the heating element: Make sure that the heating element is not broken or damaged and check the continuity with a multimeter.
6. Contact the manufacturer or a professional technician if the problem persists or you are unable to troubleshoot the issue.

Note: Before you start troubleshooting, make sure to turn off the power to the unit and unplug it from the electrical outlet.

F29 on all Frigidaire ranges means there is a communication error between the oven user interface and the touch panel. The control can't do the initial communication. This could be related to a wiring problem or a problem with the touch panel or the oven user interface board. Turn off the power to the range for 30 seconds to clear the code. If it returns, check that the wiring harness is fully seated. Check the wires for continuity and make sure that there is no corrosion on any of the pins. If the error repeats, replace the touch panel. If the error still persists, then replace the user interface board. Please add a comment with the model of the range for a parts list/diagram. I hope this helps. Cindy Wells

Hello again :>D Videos

Replace the switch...be sure to turn the Breaker to the unit off before servicing. https://www.repairclinic.com/ProductDetail/2453504?c=35 Their 800# people can assits you too, and videos on how it's done on the part discription.

bad valve on water dispenser

Sorry about that useless reply from the new poster who seems to be guessing answers and probably thinks he gets paid for points. Everything on this site is voluntary. I checked and no one else has this problem that you have, which is unusual. My guess is that you have a fault with the door switch or more likely a bad connection on the display board. If can get to it, disconnect the connectors, spray them with electrical contact cleaner and reconnect. Another possibility is some type of feedback from the driver module on these new fangled LED Lights! https://www.google.com/search?q=Frigidaire+GRSC2352AF+panel+resets+when+freezer+door+opens ..

The compressor or other electrical components have quit working. Or there has been ice that has accumulated over the coils. Or the wiring is faulty or the plugs could be loose. The cord could be frayed.You will need to have the while model to be either repaired or replaced.

Hi, Please power cycle your dryer and attempt to run it again. If this fails, please ensure that your clothes are evenly distributed so that they weight of the clothes doesn't cause the dryer to be shutdown. Just to double check, please ensure that you've cleaned the lint track of your dryer. Lastly, you can use an power outlet extender to help switch the power outlet that you're using to run your dryer as there might be something wrong with your current one. Thank you.

It sounds like there may be an issue with the water inlet valve or the wiring between the ice maker and the water inlet valve. Here are a few things you can try to troubleshoot the issue:

1. Check the water supply line: Make sure that the water supply line is properly connected and there are no kinks or blockages in the line.
2. Check the water inlet valve: Make sure that the water inlet valve is functioning properly and is not clogged or damaged. You can test the valve by jumping the two terminals with a small piece of wire. If the valve opens, it is functioning properly.
3. Check the wiring: Make sure that the wiring between the ice maker and the water inlet valve is securely connected and there are no loose or damaged wires.
4. Check the ice maker control board: The control board is responsible for controlling the ice maker and may be the cause of the issue if it is faulty. You can test the control board by unplugging the fridge and using a multimeter to check for continuity between the control board terminals.

If none of these troubleshooting steps resolve the issue, it may be necessary to consult the manufacturer or a professional appliance repair technician for further assistance.

If you have been using the self clean feature, you have probably burned out or damaged the connections to the fan and the convection fan element or thermistor. NEVER EVER use the self clean feature. https://www.partselect.ca/Models/CGEB27S7CS2/Sections/BODY/?ModelID=1073773&ModelNum=CGEB27S7CS2&mfgModelNum=&ManufactureID=4&Selected=OTRVH5GS&Position=1&mfg=Frigidaire&Type=Wall%20Oven&Mark=1

4 Reasons to Stop Using Self-Cleaning Oven Feature ...

https://fixappliances.ca > 4-reasons-stop-using-self-clea... A self-cleaning oven is a feature on many modern ovens that burns off cooking spills and splatters with an extremely high temperature (932 F° or 500 C°) to ... ‎How Self Cleaning Ovens Work · ‎Major Parts Damage · ‎Family Safety

Why You should Never Run A Self Clean Oven Cycle & A ...

https://www.generalappliancesvc.com > why-you-shoul... Jan 29, 2020 - With an inside temperature exceeding 500° C, and a flash point (the temperature at which items can self-combust without an ignition source) .....

If the door seal is that bad that it is letting all of the cold out. Put the duct tape on the left, right and bottom edges. Just enough pressure to seal.

The control panel lock is engaged. This keeps the dryer from being turned on by accident while cleaning the panel (or by a small child). There should be a line with a padlock symbol between two buttons on the control panel indicating the ones to press and hold to toggle the lock feature. On some Frigidaire dryers, the buttons to press and hold are Options and Select. You need to hold the buttons for 10+ seconds. The LOC message should disappear when you have held the buttons for long enough. However, if you do not release the buttons, the lock will toggle back on. I hope this helps. Cindy Wells

This is caused by a blocked defrost drain. The defrost cycle is normally overnight and the condensate that is defrosted from the evaporator fins is supposed to drain into a pan near the compressor where it evaporates. Look on the external and internal rear of the unit for a pipe and a u-bend.

sounds like compressor not coming on

If it is new, didn't it come with an operating manual? Videos here https://www.google.com/search?q=Frigidaire+Gallery+GRFC23534FO+sabbath+mode

How do I set Sabbath mode on my refrigerator? - Frigidaire

https://www.frigidaire.ca > ... > FAQs > Refrigerators Depending on your model, the Sabbath mode is turned ON or OFF by simultaneously pressing and holding for 5 seconds both the:"v" and "+" orThe freezer "-" and ...

Oven lock feature. https://www.google.com/search?q=Frigidaire+ples389ech+stovetop+cooking+display+is+showing+--+(two+dashes)+esec+lockout ..

Hi, please make sure that there is a pot or pan on the stove top when you start it. It might be locking as a safety mechanism if it doesn't sense an object ready to be heated. Otherwise, please refer to the troubleshooting section of you manual to help turn off the locking mechanism. Thank you.

Try unplugging the unit for 5 full minutes, then plug back in and try resetting the filter light.

On many machines the E11 error occurs as one or more of these connecting wires break, this may be due to excess movement from unbalanced loads. To prevent this when washing any heavy items ensure there are enough heavy items to spread around the drum to help the machine balance its load.

It sounds like you may have an issue with the plug that connects the microwave portion of your Frigidaire PLEB27M9ECD built-in oven/microwave to the electrical supply. Here are a few things you can try:

1. Check the power supply: Make sure that the oven/microwave is properly plugged into a working outlet and that the circuit breaker is not tripped.
2. Inspect the plug: Look for any visible damage on the plug and make sure that the connections are secure.
3. Check the wiring: Make sure that the wiring inside the oven/microwave is not damaged or loose.
4. Test the outlet: Using a multimeter, test the outlet to see if it's providing power.
5. Test the microwave: If you have access to a known good microwave, you can test the plug by plugging it into the known good microwave and see if it works.

If none of these solutions work, it's likely that there is an issue with the electronic control board or the plug itself, which will require professional repair. It's best to contact the manufacturer or a professional technician for repair. They will be able to diagnose the issue more accurately and repair it.