Frigidaire Popular Questions, Answers, Tips & Manuals

IT sounds like a bad burner switch, try replacing it.

The fuse is on the main control board and is not something that is routinely replaced. Are you sure you are not looking at the thermal cut off? Parts for Frigidaire CFMV156DCD: Oven,cabinet Parts - AppliancePartsPros.com

It is a fairly standard range if this is it? https://www.repairclinic.com/ProductDetail/1138328 Lots of help here. The answer is normally to remove the door and then put it back. It is normally not on squarely or fully home on the hinge supports. I had the same a few days ago on a GE. https://www.hunker.com/13409343/how-to-troubleshoot-a-frigidaire-oven-door-that-will-not-close-all-the-way https://www.google.com/search?q=Frigidaire+oven+broiler+door+doesn%27t+close+all+the+way ..

Are you calling the compressor condenser? My gallery side by side stopped cooling the refrigerator side and it was the control board under the refrigerator side. Also, just because the control board is new does not guarantee it is good. There are a lot of youtube videos on trouble shooting the Gallery. You might not have plugged in all the connectors when you changed the board, or maybe bent some pins.

Yes, never ever use the self clean function on modern ovens. 880-900 degrees to too aggressive. We see ovens broken here all the time, doors locks broken, wiring burnt, elements burned out, control boards frazzled, fans seized. You need a service call. There is no thermal fuse for obvious reasons, it's an oven. Self-Clean Ovens The oven is cleaned by heat, at temperatures above normal cooking temperatures. During the cleaning cycle the oven is heated to about 880 degrees Fahrenheit (471° C.). At this temperature, food soils inside the oven decompose, leaving behind a small amount of ash. Buy a can of Easy-Off, or use household ammonia. If panels are removable, you can put the parts and the ammonia into a black garbage bag overnight.

Probably the main burner safety valve. Possibly a fault with the fan. It is a gas appliance so you can't work on it yourself. You need a gas certified appliance engineer to diagnose and fix.

Water is not drained completely

The problem is with the electronic board of the device and you have to repair or replace it.

it probably needs freon and only service people can do it right

This indicates it is the High Limit Thermostat, which isn't a fuse. Most dryers have three heat related components. They usually trip because of bad airflow, check the hose at the back and the vent in the wall. This is the time that birds make nests in them! Also wash the lint filter with dish soap and a brush. Part No. 33 here https://www.searspartsdirect.com/model/55b2zm5szl-001428/frigidaire-fase7073lw0-dryer-parts The error code of E65 is a high limit thermostat trip . For Electric Model, check Inlet Thermal Limiter for continuity. If Thermal Limiter is open, check for evidence of high temperature event and any resulting damage. If no further damage is evident, replace Thermal Limiter. Jul. 27, 2017

Frigidaire dryer still codes E65 after an E64. Replaced heater ...

https://www.justanswer.com > ... > Dryer Vent Problems

sounds like the transmission needs replaced

I think that your microwave has stopped working on you guys and it needs to be replaced.

Bad connection, faulty power supply, faulty door switch. etc etc etc.

Unplug and get a pair of needle nose pliers..grab metal end of bulb and remove..

door switch faulty

is the water running into the unit check valve is open and check for clog

Try pressing and holding the Delay Start button for ~3 seconds. The 'loc' indicator should go out. If you hold the button for too long, then the lock could toggle back on. If the problem persists, you may have an issue with the keypad on the dishwasher. I hope this helps. Please add a comment with the model number of the dishwasher if the control panel lock does not disengage. Cindy Wells

Common solutions for: Frigidaire Washer won't spin or agitate. Inspect the drive belt to determine if it is broken or if it is loose on the pulleys. If the drive belt is broken or loose, replace it. If the lid switch assembly fails, the washer will not spin.

thats normal its showing ambient when you lower it the number will change to the setting and then will go back to show what the ambient temp as the room gets cooler the temp number will go down and shut off at set temp

The defrost drain is clogged or the icemaker drain line is frozen