Frigidaire Dryers - Page 5 - Popular Questions, Answers, Tips & Manuals
Broken lint screen, what are the 2 wires attached to lint screen housing?
the red wires go to the sensor,this is used for the auto dry where it might say more or less,when the clothes spin they rub up against the sensor when the clothes start to dry it senses this and advances the timer until the clothes are dry and then the dryer will shut off automatically.go here to see the part
https://www.repairclinic.com/PartDetail/Moisture-Sensor/131845801/823088
11/20/2017 8:12:04 AM •
Frigidaire...
•
1,066 views • 0 helpful votes
Frigidaire affinity dryer wont run cycle it resets
Not 100% but there should be a way to reset computer using the controls on the dryer.
If you have the manual it should be in there or contact the manufacture you could get lucky they may tell you.
Regards Craig
1/30/2018 3:57:02 PM •
Frigidaire...
•
105 views • 0 helpful votes
Start/stop lights are flashing with "50" minutes readout. should be OFF. how do I clear it for good?
these dryers have alot of board problems i've seen them beep and then start up by themselves gotta love frigidaire,the computer board took the place of the timer so if the dryer didn't advance to off and got stuck in the same spot you knew it was the timer,so if it doesn't count down and beeps it sounds like a board issue and sometimes the board can't read itself out and you won't get a code.try unplugging it for like 5 to 10 minutes and then plug it back in to see if it resets the board but it probably will go back to doing the same thing
1/11/2018 11:39:02 PM •
Frigidaire...
•
171 views • 0 helpful votes
Clothing gets caught on lint trap
If your dryer is new, it will have warranty a on it. Request a home visit from an authorized technician at no charge to diagnose/document your issue.
Due to fabric damage, once the cause is determined and corrected, contact the manufacturer for a possible compensation for the damaged items. Take pictures and provide receipts. I’m happy to assist further over the phone at
https://www.6ya.com/expert/david_dc2f9e0a44104720
11/24/2017 6:51:03 PM •
Frigidaire...
•
548 views • 0 helpful votes
Felt liner on right front
It actually sounds like you have another problem that is causing this one. When you remove the front to access the felt gasket check the support rollers because you might have one or both that need replacement. I would suggest replacing the felt also and yes it does require the high temp adhesive.
1/1/2018 2:51:03 PM •
Frigidaire...
•
130 views • 0 helpful votes
Frigidaire dryer dryer will not run starts for 5sec then stops
frigidaire dryers have alot of problems with the control board,if it starts then fuses are good or it wouldn't run,does it start right up again?if so you have a bad board,if it doesn't start right up again the motor most likely is bad,any error codes?you could have a bad or broken wire somewhere in the dryer but like i said,they have alot of board issues,next time send the model number,if you know where the board is open up the dryer,unplug it first,then when you find the board plug the dryer back in and start it,when it stalls try tapping on the board,it might start again,if not unplug the dryer and look at the board to see if there's any burn marks on it or a bad soldier joint,also it might have a burnt smell to it.
12/31/2017 3:34:45 PM •
Frigidaire...
•
110 views • 0 helpful votes
Kenmore model 84152/94152, 8 years old, started
that isn't a model number and kenmore doesn't make anything so you have to send the full model number off of the dryer,open the door look around the opening where you put the clothes in and send the model number,if it's beeping and starting on it's own it sounds like you have a computer board problem with it but can't help you without the model number.
12/31/2017 6:45:03 PM •
Frigidaire...
•
109 views • 0 helpful votes
Frigidaire combo washer/dryer screws inside come off
The drum shaft came loose from drum. You can YouTube it for procedure of disassembly of dryer. Remount shaft, if screws are bad may need new shaft with screws, make sure it is tight to drum. While you have it apart you can clean out lint.
9/27/2017 3:54:03 AM •
Frigidaire...
•
1,094 views • 0 helpful votes
Not finding what you are looking for?