Frigidaire Dryers - Page 4 - Recent Questions, Troubleshooting & Support

Broken belt perhaps?

Could be the start button or the timer.

The code E68 indicates that a button is stuck. Check the buttons by pressing them one by one to find the stuck button.

The E9X codes all point to a faulty control board, as does the fact that the PF code canno tbe cleared. Just make sure none of the buttons are stuck down before you replace it...copied from another forum im in

If the dryer has dual or triple heating elements, one element, or the relay controlling one element, could be open circuit, ( failed). mostly likely is a failed heater element. The elements work together or separately to combine the heat settings. there could be a high and low element, that do the different ranges. it could be that when it is on medium or high, it's really a lower combination of heat, and it may not be easy to observe, but on the low settings, the chosen element is completely open and failed and provides not heat at all. if medium and high are really low and medium, and low and medium-low is really nothing, then 1 element is probably open circuit. ( failed).

Moisture sensor

Have you checked the belt maybe b broken

Request from Frigidaire

If you use fabric softener sheets in your dryer, they eventually will deposit enough residue in your lint trap to close up the mesh. Usually you cannot see the residue, although it is blocking the movement of air through it. My advise would be to remove the lint trap and run it under hot water and clean it well, then try the dryer with the clean lint trap. I hope this works for you and solves your problem.

Fifa M?nzen https://de.fifacoinszone.com Kaufen Fifa M?nzen https://de.fifacoinszone.com Kaufen Fifa M?nzen PS4 https://de.fifacoinszone.com/category-fifa19coins-ps4.html Kaufen Fifa M?nzen Xboxone https://de.fifacoinszone.com/category-fifa19coins-xboxone.html Kaufen Fifa M?nzen PC https://de.fifacoinszone.com/category-fifa19coins-pc.html Fut M?nzen https://de.fifacoinszone.com Fifa 19 M?nzen https://de.fifacoinszone.com/category-fifa19coins.html Kaufen Fifa 19 M?nzen https://de.fifacoinszone.com/category-fifa19coins.html G?nstige Fifa 19 M?nzen https://de.fifacoinszone.com/category-fifa19coins.html Fifa 19 ultimate team M?nzen https://de.fifacoinszone.com/category-fifa19coins.html Fifa 19 M?nzen PS4 https://de.fifacoinszone.com/category-fifa19coins-ps4.html Fifa 19 M?nzen Xboxone https://de.fifacoinszone.com/category-fifa19coins-xboxone.html Fifa 19 M?nzen PC https://de.fifacoinszone.com/category-fifa19coins-pc.html G?nstige Fifa M?nzen https://de.fifacoinszone.com

Check the owners manual or manufacturers website for error codes. Most likely cause...a bad control board.You tube will most likely have "how to replace" videos for your assistance. Good luck...

Typically there is a wiring diagram inside console area or on back of dryer.

That error is an E5b error. This indicates a problem with the heating element, the thermistor or the control board. You'll need to unplug the unit and access the wiring. Inspect the heating coil for breaks. Then test the voltage across the element (should see the line voltage) and check the resistance at the thermistor (should be ~50000 Ohms in a room temperature environment). If the above are okay, your control board is probably bad. If you post a comment with the model number, I may be able to point you the appropriate parts. If your dryer is under warranty, contact Frigidaire. I hope this helps. Cindy Wells

Searspartsdirect.com

Either it’s not latching properly or there’s a control board issue

Heating element or fuse / thermostat most likely bad.

It should be labeled as such in control panel around timer.

Check for fluff and lint in vents and inside dryer vacuum it out

If it were me, I'd probably just clean up the scratches on the pulley and or motor shaft. You can do so with a small file or sand paper. If you believe the friction caused by this roughens is due to the scratches, try smoothing them down. The grooves remaining won't harm the belt or pulley, but raised edges could. When I worked in an electric motor shop, we repaired many a motor shaft by filing the bad nicks caused by pliers and wrenches, with a little filing as the motor turned.

Did you put the belt back on correctly?