Fahrenheat Popular Questions, Answers, Tips & Manuals

What is this? please give exact details.

you may have 115v/120v instead of 208v/230v. check connection at wall switch or j-box.

You need to check the breakers or the actual power because I see the 1614 model as being 240 Volts. Unless you can change that rating inside the unit itself and it has been set to 120 Volts. IT appears from the wiring code you listed that the building wires are 120 volts. However a meter would be the definitive answer. When you are running 240 or higher (double phase) Black and Red are hot and white is neutral If it is 110 then black is hot and white is neutral. Since I cannot tell from the description posted whether the red is source or inside the heater, you really need a volt meter.

check your amps, possibly a bad limit switch, possibly a bad element. If you need further help, reach me via phone at https://www.6ya.com/expert/thomas_092728000e6acb79

You could do it. It would mean serious wiring though and you should use the factory thermostat because it is designed to operate on 240 Volts. Or you could use a remote thermostat at low voltage to throw a relay in the heater and get it to come on. The manual has good diagrams on how it is wired and it would not be too hard to do. IT would operate just like the outside unit on an HVAC system .

Turn the power off and make sure all connections are tight. How do you know it's getting very hot? Are you touching it? Is this an actual terminal block or a breaker or is it inside wire nuts? Are you able to check amps AND are you heating or cooling??? Thanks If you need further help, reach me via phone at https://www.6ya.com/expert/thomas_092728000e6acb79

Sounds like possibly you haven't removed all packing material. All machines will produce a strange odor upon start up but should go away rather quickly. Be sure to Read the manual in it's entirety If you need further help, reach me via phone at https://www.6ya.com/expert/thomas_092728000e6acb79

Im.sure there is safeties on access panels. Put it back together and try again. Be sure you have removed all packing material!! Your element should begin glowing in seconds. If you need further help, reach me via phone at https://www.6ya.com/expert/thomas_092728000e6acb79

It's likely shutting off on a safety. It needs cleaned. Possibly a filter change. If you need further help, reach me via phone at https://www.6ya.com/expert/thomas_092728000e6acb79

#1 you have to calculate the heatloss of your rooms,that will tell you ur wattage require. Oil filled or not,it's just as dry. As far as ur load to panel breakers, a rule of thumb is approx 3600 watts for 20 amps,using a number 12 wire. But ur wall heaterS should suffice

farenheat bennettsville, s.c. part number is 5216-2007-000 for the switch, however a qualified electrician should check further for problems beyond the switch.

Your best bet is to call your county inspector. Every County is different, for that matter, every inspector is different. Good Luck!! If you need further help, reach me via phone at https://www.6ya.com/expert/thomas_092728000e6acb79

The copper wire is the ground .

You may have to put a few drops of machine oil on the motor shaft. There is a felt washer on both ends of the motor shaft that absorbs and stores the lubricant. It probably is dry.

www.AppliancePartsPros.com

Here is the link for the owner's manual. Or call customer service at 1-800-654-3545. http://www.manualshelf.com/manual/fahrenheat/fzl4004/instructions-assembly.html

all you can do really is clean them as best as possible

therte is no neutral wire when wiring 240v ( 2 black 1 ground usually)

heater stop working outlet works but heater doesn't work need some suggestions