Faberware Coffee Makers & Espresso Machines - Page 8 - Recent Questions, Troubleshooting & Support

Hi. The spring slips onto the stem just under the coffee basket, it holds the stem with pressure so the perked coffee go up the stem onto the spreader, check repairshack.com Ron

Hi, The problem is the keep warm element. The reason, your pot perc's and it gets hot near the thermo, the thermo turns off the main element. The keep warm element is not on so after a small amount of time the water cools and the thermo turns the main element back on again, thus making the water hot. The K W element is supposed to be on all the time the pot is plugged in, it is instrumental in perking the first brew making it really hot, the thermo turns off the main element and the K W element keeps the water hot. The K M element is very a easy fix. Thanks and please ask if you need more help. Ron For the part go to repairshack.com

Hi you need a prong assm. [email protected] bobbyone

The problem is the keep warm element. The reason, your pot perc's and it gets hot near the thermo, the thermo turns off the main element. The keep warm element is not on so after a small amount of time the water cools and the thermo turns the main element back on again, thus making the water hot. The K W element is supposed to be on all the time the pot is plugged in, it is instrumental in perking the first brew making it really hot, the thermo turns off the main element and the K W element keeps the water hot. The K M element is very a easy fix, it is the small looking white rope that runs around the bottom of the pot. You have 1-nut and 1- screw to remove. When removing the screw from the main element you must hold the (leg) that the K M element is screwed to so it does not bend and brake off. Take your time and be firm with the pressure you apply to the screw, while holding it with a pliers. Part is 8.00 plus 2.00 S/H. bobbyone

Hi. Yes I have the parts. [email protected] bobbyone

Hi, you use 3 scoops of coffee for 4 cups. Then go to what you like. bobbyone

Hi. 3 scoops of coffee to 3 cups, Them adjust from there, bobbyone

Hi, Go to repairshack.com Good luck bobbyone

Hi. You need to replace the prong assm. [email protected]. bobbyone

The problem is the keep warm element. The reason, your pot perc's and it gets hot near the thermo, the thermo turns off the main element. The keep warm element is not on so after a small amount of time the water cools and the thermo turns the main element back on again, thus making the water hot. The K W element is supposed to be on all the time the pot is plugged in, it is instrumental in perking the first brew making it really hot, the thermo turns off the main element and the K W element keeps the water hot. The K M element is very a easy fix, it is the small looking white rope that runs around the bottom of the pot. You have 1-nut and 1- screw to remove. When removing the screw from the main element you must hold the (leg) that the K M element is screwed to so it does not bend and brake off. Take your time and be firm with the pressure you apply to the screw, while holding it with a pliers good luck. bobbyone

Hi. Go to repairshack.con for parts. bobbyone

Not a stupid question, are you turning it counter clockwise. I have the parts you might need. bobbyone

Go to [email protected]. bobbyone

Hi. go onto eBay and look for Corning coffee pot parts. bobbyone

Yes, go to [email protected]. bobbyone

Hi. It can be fixed, but the cost will be high. You can not gets parts for them. I repair them and have to make the parts I need.. bobbyone

Yours is probably a China pot. They are inferior to the USA. I suggest you go on eBay and buy a used one. that will last for years. bobbyone

Hi. The base is not supposed to get hot.. If it was perking you would hear it, for Farberware makes a lot of noise. I need more info. bobbyone

Hi. Go to repairshack.con. Good luck. bobbyone

Hi. Contact me for instructions [email protected] bobbyone