Element Electronics Televison & Video - Recent Questions, Troubleshooting & Support


I lost the screws for my legs for my 50 inch element TV????

Element... | Answered on Mar 14, 2019


Ok, I am having the same issue. I just bought my tv - same model at the Target Black Friday sale. Can I ask, did yours make a low humming noise before you changed it out. I still am within my 30 day exchange policy, so I am thinking it would be wiser just to exchange it... but my concern is, would I get one with the same problem (or worse) in exchange?

Element... | Answered on Feb 15, 2019


Some sets and devices have HDMI control that can turn off and on devices connected to them. Look into the settings of both devices and search for anything to do with HDMI control.

Element... | Answered on Dec 30, 2018


YOU PLUG IT IN AND TURN IT ON NO SETUP SHOULD BE REQUIRED

Element... | Answered on Dec 17, 2018


you can go to menu options, than find programming options.
Look for an option called "autoprogram" and select it. It will search and set all available channels.

There is universal remotes for this tv that you can find by googling "elements electronics remotes":

Element... | Answered on Dec 05, 2018


Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts.
http://electro-medical.blogspot.com/

In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.
Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.

Element... | Answered on Apr 22, 2018


Without its remote control, you can't do a system reset to this set.
Try a Hard Reset to this set, and then check.
There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts.
https://electronicshelponline.blogspot.com/
Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.
If a hard reset do not help, you should buy its original remote control from its authorized service center.

Element... | Answered on Feb 17, 2018


There aren't any buttons to push on the remote. There are 3 main boards in the TV: Power supply, main, and T-Con board. Do this test. With the TV on shine a flashlight on the screen and look for a faint picture. If you don't see one, then the T-Con board is bad. If you do see one then the backlight driver is not turning on the the white light for the screen. This driver can be on the power supply or the main board. It depends on the model. Since your TV is 10 years old you may want to get a new TV.

Element... | Answered on Feb 14, 2018


it could be the t-con board going. or the screen connector ribbon is lose. or even just the connection cable to the t-con board. if you push gently around the edge of the screen if the pitcher gets better or worse then its the screen connections. sometimes can be fixed with cracking the cable or slightly heating the area and packing, but this is with the led screen panel out. but would think its more a t-con board filing.

Element... | Answered on Feb 13, 2018


take to a repair shop for repair estimate . it is 8 years old and nothing fixya can do for you

Element... | Answered on Dec 08, 2017


Bad power board, it could be a regulator circuit in the board and you can troubleshoot it if your good at electronics as those switch mode power supplies can be a little tricky sometimes, it may make more sense to replace the board though, generally they aren't that expensive, under 50 bucks generally

Element... | Answered on Dec 01, 2017

Not finding what you are looking for?
Element Electronics Logo

1,325 questions posted

Ask a Question

Usually answered in minutes!

Top Element Electronics Televison & Video Experts

Cindy Wells

Level 3 Expert

6034 Answers

LP

Level 3 Expert

514 Answers

Are you an Element Electronics Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...