Electrolux Washing Machines - Recent Questions, Troubleshooting & Support


How much trouble do you want to go to?

If you just want to preserve the washing, then simply put it on another cycle tonight and that will keep it fresh until the callout turns up to fix it.

The next clever step is to power the machine off at the mains for 10 minutes. Depriving it of power MAY release the interlock door switch even if the cycle didnt.

Final attempt to get to it... Turn off power, unplug at the mains. drag the machine out so you can see the back. Remove the 2 screws that hold the top on, pull back or tap the top forward (depending on the model) to unclip it. Peer inside. You will see the door switch inside the chassis exactly in line with the door handle on the outside. See if you manually make the mechanism release, or if you have a stubby philips screwdriver, you can probably unscrew the switch complely.

If you trust yourself NEVER to open the door in the middle of a cycle, the machine will of course function without a switch. Just so long as you recognise that you will flood the place if you do open it with water in. Also if you put your hand inside dirung a wash (Or worse still a spin) the power of the motor combined with the weight of the wet washing will rip the arm clean off a fully grown man, so if you doubt yourself or you have kids (or kids may visit) don't leave it like this.

Electrolux... | Answered 22 hours ago


check the top edge of the front panel, sometimes there's two clips, one on the left top and one on the right top of panel. undo the clips and it should come off. Or if there are no clips you might have to just lift up to clear a notched edge. Clips could also be on the bottom, Either way most machines have a second way of holding the panels or tops on. hope this helped.
Lynn

Electrolux... | Answered on Mar 17, 2019


It sounds like the water level sensor needs replacing if it is overfilling, but that is not what E10 says here.

Try this
https://www.youtube.com/watch?v=eGRAc5G7y7k

Washing machine displays error message E10, C1 or emits 1 beep / 1 flash. It indicates problem with not taking in water, not taken in enough water or problems with the drain.Feb 20, 2019

Washing machine displays error message E10, C1 or ... - Electrolux


https://www.support.emea.electrolux.com/.../Laundry/...Washing_Machine/The_washing...

How to Test a Washing Machine Water Level Switch - The Spruce


https://www.thespruce.com > Home Repair > Electrical Repair > Electrical Appliances

7 days ago - A faulty water level or pressure switch is one such device. ... The water level switch sends power from the timer control to the water inlet valve and the temperature switch each time the tub needs to be filled during a wash cycle. ... As the washer fills, water enters the tube from the ... https://www.google.com/search?safe=off&ei=wE58XIymJcvt5gKZvJOYCw&q=electrolux+washing+machine+water+level+sensor

Fixing E10 Errors

https://www.google.com/search?safe=off&ei=Rk98XMKBGsic5wKqsq7wCg&q=electrolux+washing+machine+e10+error+message&

How to fix Electrolux error code E10

Electrolux... | Answered on Mar 03, 2019


hello... it may help...

error descr. cause action reset E43 Power triac on door interlock faulty Door safety interlock faulty; Wiring faulty; Circuit board faulty. Safety drain, door released Selector on "0"

Electrolux... | Answered on Feb 20, 2019


find reset function bottons find youtube video how to reset your brand model or similar model and follow instructions on your owners manual

Electrolux... | Answered on Feb 15, 2019


Can you turn off your overdrive? When towing most vehicles have an overdrive off mode. You can’t tow in 5th or 6th gear and may confuse computer and put car in protection loop mode.

Electrolux... | Answered on Feb 13, 2019


I don't think you have all the correct error code. should be an "F" number before the "E" number. does make a difference. I want to give you the correct info.

Electrolux... | Answered on Feb 12, 2019


If you remove the drain hose, and lay it down low as possable, it will drain the water out by gravity, this might help you out.

Electrolux... | Answered on Feb 11, 2019


You may need to remove the front panel like on my Frigidare washer. Removing the retaining spring ring holding the seal may be tricky.
I learned from watching a repairman do it.

My filter got clogged because the drum impellers tend to break a piece and let change and stuff go to the filter.

Electrolux... | Answered on Feb 01, 2019

Not finding what you are looking for?
Electrolux Logo

2,346 questions posted

Ask a Question

Usually answered in minutes!

Top Electrolux Washing Machines Experts

Brad Brown

Level 3 Expert

18002 Answers

jimorris77

Level 3 Expert

411 Answers

Kolbrun...

Level 3 Expert

1215 Answers

Are you an Electrolux Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...