Electrolux Air Purifiers - Popular Questions, Answers, Tips & Manuals
Resetting filter indicator on Electrolux oxygen air purifier
Hi! I hope this tips might help you out .
*Plug in air cleaner and press POWER button until short “beep” sounds. . Press the RESET FILTER button by gently inserting a paperclip into the RESET FILTER hole on the control panel. The light will flash 5 times before a “beep” sounds to indicate the filter has been reset.
Thank for using fixya .
Oven stopped working after self clean
Electrolux Double Oven EI30EW45JS1
After a self clean cycle the top oven stopped heating up. The keypad was operational, but there were no error codes. I determined this was due to the thermal switch being tripped. Unfortunately the oven has to be removed from the wall to get to the back where the switch is located.
Here is what I did:
1) Remove any trim around the oven in prep for sliding it out (see installation instructions).
2) Slide it out with a friend, on to a hydraulic table cart (1 used a 500 lb capacity one)
3) unplug the oven and remove the back panel.
4) Either reset the thermal switch by pressing the red button, or replace it. I found mine located on the upper left (facing it from the front)
5) replace the back panel
6) plug the oven back in
7) slide it back in place
8) replace the trim
The hardest part is getting the oven out, so I just replaced the switch and everything worked fine.
After removing six screws, how do I get case apart to repair electric cord
www.fixya.com/.../t25091002-
replace_
power_
cord_electrolux_nimble
Sep 11, 2014 - Power cord is frayed next to body, need to replace it. how do i get ....See all Electrolux EL8602A Nimble Upright Bagless Vacuum Questions.
www.amazon.com/...
EL8602A/.../B004GUFWBM
Amazon.com, Inc.Electrolux Nimble Upright Bagless Vacuum, EL8602A ... The rotating brush on/off buttons are located right under the soft-touch power button high up at .... Cord is a $30replacement part, which I'm regretting not doing from the get-go, due to ...
4/13/2015 6:16:19 PM •
Electrolux...
•
1,326 views • 0 helpful votes
Dryer display blinks on ND OFF WHEN TURNING DIAL or pressing start and does not turn on
I appreciate your post, friend!
From the information you have provided your Electrolux dryer's displays blinks on and off when you turn the dial and it does not start. This sounds like a possible issue with your door latch or control panel. I would recommend for you to check the door strike and door latch to make sure there is no visible damage. If you do not see any damage this could be a wiring issue within your door latch or control panel. This is not a simple DIY job and I would suggest having a professional out to perform an accurate diagnosis. I hope this is helpful information. -Matt
3/1/2015 3:00:25 PM •
Electrolux...
•
264 views • 0 helpful votes
Beater bar on electrolux el8602
Usually you have to replace the belt or if it is burning up belt take beater bar out and check the ends to see if they turn. Sometimes they get thread up in them from carpet and get stuck from turning and then they will burn belt up. Rich
12/21/2014 4:04:50 PM •
Electrolux...
•
203 views • 0 helpful votes
Can't open vacuum bag compartment
The release button may be stuck or jammed, try pushing in on it and at the same time tapping the area around the button with a heavy wooden spoon, it may be enough to free it.
Have a lux legacy c 153c made by aerus comes on and runs fine for maybe 90 sec then shuts off and in about 90 sec will come back on .has great suc and runs great while runing
Is the motor overheating? Or is it more like there's a loose connection in the on/off switch? What happens if you reel in the cord a little? Could be there is a spot somewhere in the rings which is corroded or worn out and not making contact. Might also be a break somewhere in the winding inside the motor.
I have a similar situation in my Aerus C15C3. An Aerus brand bag ruptured inside my vacuum cleaner, but I didn't realize until the motor started making a horrible noise! To make matters worse, I hooked up my older Electrolux LE 1623 and at tried to suck as much debris out of the air intake at the bottom of the bag compartment, and then put the C15C3 back into service. I should have stopped then and there and started working on trying to get the motor and the fan out of the housing. But my machine was overheating and shutting off.
Sears Parts Direct has diagrams of the Electrolux LE 1623 on their website. The good thing about Aerus and the old Electrolux-USA is that they all have similarities in their design, but Aerus does like to tweak their design just enough to foil or at least complicate access to DIYers and general vacuum repair shops.
I hope you post what you find out!
How to dissasemble
This is a general response but I have found most of them to be the same way. Take off all panels and access doors that you know come off. On the bottom or side of the unit you will see deep hole molded into the body. If you flash a light down you will see a screw head with a Phillips head or Torx bit. You will need a long screw driver with that bit on it or an extension that will fit. There will most likely be about 6 of those to remove.
5/21/2014 6:34:57 PM •
Electrolux...
•
108 views • 0 helpful votes
Not finding what you are looking for?