Dynex Televison & Video - Page 2 - Recent Questions, Troubleshooting & Support
How do i reset factory settings on dynex tv
To know more about this, you have to download the repair manual to this set. Try this link to get a repair manual in PDF. It has all details.
72513882 Dynex Hisense Service Manual DX L40 10A pdf
As Dynex & Hisense sets are fitted with similar kits. The procedure to enter the service mode, and to do the factory settings to both the brands will be the same.
If you wish to get some details; check the site linked here. Viewing it in "
Mosaic" or "
Magazine" will make surf easy. Pull up older posts. Surf the site with patience.
Do a search by type in the brand name of your device at its search box and press "Enter".
http://electronicshelponline.blogspot.com/
Service mode entry, adjust and exit procedure to many popular brand TVs are given.
Never forget to exit the service mode, after all adjustments have been done.
My Dynex TV will not power on, but the LED light is blue.lije it's on, but nothing
As the blue light is ON, the power section board is functioning almost right. The fault be in its main board. It will be best to contact any service technician in this case. If you wish to get some details; check the sites linked here.
https://elektrotricks.blogspot.com/
https://electronicshelponline.blogspot.com/
Faults & possible causes to LCD screen are given with illustrations. You can get an idea about the fault. Search the site by type in the Brand Name of your set, in its search bar at the right side column, and press enter. See it in by Webview with mobile or by desktop. Mobile View has no search box. Screen-shots to defective LCD panels are given. You can see and compare to that to your TVs', and can make sure about the fault to an extent.
Remove subtitles from Dynex TV DX-19E220A12. Anyone know how to do this please? Thank you.
What is the TV source (input)? Usually the captions are only controlled by the TV if your source is Antenna/Cable (using the RG-59/RG-6 cable input). If your source is a set-top box (HDMI, component or composite video), consult the documentation for that source.
If your source is set to TV, press Menu (on the remote or the side of the TV). Use the Left/Right arrows (or the Channel buttons on the TV) to select Settings and press Enter (input button on the TV). Use the Up/Down (or the volume on the TV) arrows to select Closed Captions and press Enter. The highlighted menu item should be CC Mode. Use the Left/Right arrows to choose Off. Press Enter to save the setting. Then press Menu to change another setting or Exit to leave the on-screen menu. See page 31 of the user manual available from ManualsLib here:
https://www.manualslib.com/manual/445548/Dynex-Dx-19e220a12.html . The current link to the page is
https://www.manualslib.com/manual/445548/Dynex-Dx-19e220a12.html?page=35#manual .
Some set-top boxes will have a caption control button on the remote control. Others have more difficult steps. On my IPTV box, I have to press Menu, select Settings, then enter a pass code provided by my provider. Then I enter the Hardware settings and find the closed captions menu under Audio Settings. On an old Dish receiver, the caption controls depended on the system mode. Since the receiver could serve a primary and secondary TV, captions could be viewed on the primary set or both. They could only be changed at the primary TV.
I hope this helps.
Cindy Wells
What chanel do i need to have the dynex tv on for dvd player
This will depend on how you have connected the DVD player to your TV. If you have used an HDMI cable into the back of the TV the port, (the hole it goes into), will be labelled as "HDMI" followed by a number. On your TV remote there will be a button where you can switch between input source. I think on your remote it is the 'INPUT' button at the top left corner of the remote. This will list all the ports available. Use the up, down and enter buttons to select the one matching the HDMI number you plugged into. This should switch screens to show the DVD player screen.
Dynex Flat Screen 22" w/DVD
When the picture goes out, try to open and access the TVs menu using the Dynex remote. if the menu fails to open up you can bet there is a problem with the backlight on the TV. Letting the TV rest and then it working again indicates heat as the source of the problem. Check to see if your still in your 1yr warranty or if you have a protection plan at best buy, the TV needs help.
If the Menu were to still open, you can blame your cable/satellite set top box.
I have static sound when tv is on
If it is HD make sure that all the chords are put in the right spot. Make sure that the right colors are in the right spots as well.
Not finding what you are looking for?