Dewalt Tools & Hardware - Others - Page 7 - Recent Questions, Troubleshooting & Support


I think you have to call the service center on this one,
http://www.dewalt.com/Find-Service-Center.aspx

Dewalt Tools &... | Answered on Feb 09, 2015


No - this nailer must be oiled (5-10 drops directly in air fitting before each use)

Dewalt D51256K... | Answered on Feb 07, 2015


A few things to check - some may seem overly obvious but humor me:
1) Check your nails - make sure they are the correct angle and gauge
2) Check to make sure there is not a piece of a broken nail in the nose
3) Check the driver blade & insure it is not bent or chipped
4) Make sure the nail carrier spring is pushing nails forward and isn't getting hung up

Dewalt DC628K... | Answered on Feb 07, 2015


Detail You can find the owners manual and parts breakdowns here

Dewalt 1 - 1/4 -... | Answered on Feb 07, 2015


5-10 drops directly in the air fitting before each use.

Dewalt Tools &... | Answered on Feb 07, 2015


Remove 2 screws on metal front cover.
Remove screws holding handle halves together and carefully separate (Be careful because trigger spring can fly out on you).
This will expose the belt and allow replacement. There is a spring loaded idler pulley so removal & replacing is easy.

Dewalt DC618KA... | Answered on Feb 07, 2015


That would usually be performed by a spring - is it OK?
25403509-453em5qn1uewfye2dfkecdof-4-0.jpg

Dewalt Heavy -... | Answered on Feb 06, 2015


I think that model is on a ring internally so there isnt a way to do like the bigger ones, you would have to take the screws out and take in half and you will the the brushes and can replace.

Dewalt Tools &... | Answered on Jan 12, 2015


you are going ot need to take it apart and see where it is corroded. there is most likely corrosion around the power supply to the laser itself.

Dewalt DW071KI... | Answered on Jan 09, 2015


The clutch is defective , you can get replacement parts from dewalt. There are several dewalt service centers in the US

Dewalt Tools &... | Answered on Jan 07, 2015


Use an Allen wrench to loosen the two or 4 bolts on nose of the gun. Take the plate off and remove offending nail.

Dewalt Round... | Answered on Jan 07, 2015


Did the light on the charger indicate that it was charging? (Most also have a "replace battery" or similar light.)

If so, and the drill keeps beeping...since it's new don't bother monkeying with it. Just take it back to the store and have them replace it. Dealing with a warranty repair will leave you without a tool for some length of time.

Dewalt DCF885C2... | Answered on Dec 31, 2014


To do the dew one must see the dew and then become the dew.

Dewalt Tools &... | Answered on Dec 30, 2014


Take a look on amazon for it: Amazon com dewalt trigger valve I hope this was helpful. Have a nice day

Dewalt D51256K... | Answered on Dec 21, 2014


The answer "Go to Dewaltservicenet" can be confusing - the actual site is servicenet.dewalt.com and even then, entering your part to get to manual can be infuriating. This is the link for the current model which, for all intents and purposes, is the same. The link to the helpful page is: http://www.dewalt.com/tools/woodworking-sanders-orbital-sanders-d26441k.aspx . You'll get a pop-up box with a dropdown that has a few numbers, nothing else. Just click on "1" and ignore language that indicates that this model has more than one - it does not. After you click on "1", the pop-up disappears that you're on the d/l page. Downloads are in the upper right corner. You want "Instruction Manual".You should get to this page: http://servicenet.dewalt.com/Parts/Browse#6229 but may not, it's very glitchy. On this page, you'll want to make sure "Sanders" is on the left and "sheet" is on the right. If you try to get the Manual from the DW411 page, a blank page will open. Make sure your pop-up blocker is off or that you allow dewalt.com. The instructions for the d26441k are identical to the dw411 - same technique for loading sanding sheets, same rods, etc. I've uploaded the d26441k page manual .pdf so that should help. It's easy to get lost on the Dewalt site while trying to find somthing so simple. :)

f0c3154e-e1c1-4a6d-8d3e-9ba3ad01da75.jpg


palm-sander-yluxjdg2zxd4fvyg5yprmnib-5-2.jpg

Dewalt DW411... | Answered on Dec 14, 2014


why would you want to take it a part?

Dewalt Tools &... | Answered on Dec 07, 2014

Not finding what you are looking for?
Dewalt Logo

618 questions posted

Ask a Question

Usually answered in minutes!

Top Dewalt Tools & Hardware - Others Experts

John Trevino

Level 3 Expert

1407 Answers

Ruben Bustamante

Level 2 Expert

120 Answers

john h

Level 3 Expert

21945 Answers

Are you a Dewalt Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...