Dell PowerEdge - Answered Questions & Fixed Issues

Dell PSU Z930P - if no LED lights, then replace 1 capacitor on the PWM and PFC controller module. You have to desolder that module to make this work. This capacitor has bad ESR. Replace with new, good, LOW ESR. Large capacitors at the input of the unit may have a slightly convex appearance and some decrease in capacity, but the power supply can continue to work successfully. Two small caps 100*25v on the main board can loose ESR too. If you want, replace all them with new ones for complete happiness.

sounds like a faulty memory chip in dimm 1 position

try here https://downloads.dell.com/manuals/all-products/esuprt_ser_stor_net/esuprt_poweredge/poweredge-1650_reference%20guide_en-us.pdf

What error s it giving you? Have you tested the chip to ensure it's not faulty to begin with?

• Seagate does not supply drivers for SATA drives because hard drives themselves do not require specific device drivers. Operating systems such as Windows XP/2000 may not automatically recognize the SATA controller in the system. This is especially true if the hardware is newer than the operating system.
• Try ti find the exact driver for another O/S then install it in "compatibility mode" , it may work so

Depending on the RAID setup you have for your server. Best thing to do is search for "Dell Open Manage" software for your server and install it https://www.dell.com/support/home/us/en/04/drivers/driversdetails?driverId=R108443&osCode=WNET&productCode=poweredge-4400. Once installed it will give you all the information about your hardware. you should b able to rebuild RAID with same size drive if previous drive is bad, RAID will build automatically and take a long time to complete,

I would start with reseating the RAM and disconnecting and reconnecting motherboard and system connections as there is a chance that something got rattled in shipping. Where was it before it was in Panama? Maybe the power system is different and you might need a different power supply?

a waste of time and effort installing win xp on anything as it is no longer supported by Microsoft and had real problems with drivers for just about everything install win 10 and it will work

It might not be a driver. It might be the monitor. Try another monitor.

using a DELL 13 year old server... 850 model.REDUX #3, (im almost up to speed on YOUR GOAL)you bought the wrong server, sure been there done that. and discover to your chagrin that the SATA portis useless for SAS new drives.well it is. sorry.not only that those 2 ports are slow, Intel ACH7 chips are Slow.but so is that old Pentium inside.omg some with CELERY chip dogshttps://www.dell.com/downloads/global/products/pedge/en/850_specs.pdfi see that call SAS SCSI back 13 years agook that cute, historically.the CTO order new server had 10 choice on just the controller (drive) with cables for datapower , backplane and cage, all missing in yours.there is only 2 cures.1: buy the dell parts missing in your server.card + cable + sas cage (and matching backplane)I bet only uses ones exist now,ask DELL that.2: buy a cheap raid card, and flash it to HBA mode.JBOD mode.https://www.cnet.com/how-to/how-to-turn-old-hard-drives-into-one-large-drive-in-windows/now some images sometimes the limit, is firmware, or the driveror simply , Dell didnt have 2+TB hDD to test back in 2005.!reality of that fact.

From the manual, it says minimum of 128 meg to work, so I assume the problem is with the Linux installation. If the Linux is expecting 512 and does not see it, it probably won't work. Being as you have 4 chips installed, have you tried removing two of the ram chips?

there is a problem with memory, try to open the memory card, clean the existing part of the gold layer with pencil eraser, often appear rust because of heat, after clean up, back in the place

Use GOOGLE and SEARCH for: First Search for: Dell PowerEdge T300 Server list of Error codes (12,600 hits) then search for: Dell PowerEdge T300 Server Error code "2900-0325" (You will find 40 'hits') Anthony

No we do not have that.

Not sure what "the drive forks" actually means. The floppy drive usually connects via a dedicated connector on the motherboard by a ribbon cable similar to the IDE cables but physically smaller and of course to the power supply. If the drive, the cable and the motherboard is ok it should appear in the bios list ready to be enabled and added to the boot order. If the floppy drive doesn't appear in the list you should refer to the motherboard manual as there might be some jumpers to reset or perhaps it is only suitable for a usb floppy drive. Take the number from the motherboard and do an internet search which should direct you to a place where you can download a manual which will contain all the information you need.

Have you issues FSCK command to check for disc errors?

If you are using an image made from the IBM and it has a different processor and the board specs are different that can cause the drive not to boot it will act like it is then go into a perpetual boot. I would try to re image it again to insure that is ok on the drive also check the board If one is and AMD and the other an Intel then that would be part of the problem.

too old hardware ?, more memory or harddrive size

Install another cd unit that is recognized by bios so you can install the software. Without that you can do nada! If another known good player is used and it also is not recognized then you have an issue with your CMOS - not a good thing!!!!!!!!!!!!!!!

DriverPack Solution driver update software Download Windows 7 XP 10 8 and...