Datalogic Recent Questions, Troubleshooting Help & Support

Here's the link for the manual, though I didn't see direct instructions on how to set display brightness: https://www.elzab.com.pl/download/io/FalconX3instrukcjaObslugi.pdf I saw on Page 50 the Display icon on the desktop. As this is a Windows CE operating system environment, most likely the display brightness can be adjusted there. Hope this helps, I don't have specific working knowledge of this particular device.

1. Download Product Reference Guide (PRG), Gryphon I GD4100/GBT4100/GM4100 and Gryphon L GD4300 (English) Manuals . 2. Go to Page 80, Section titled GS1-128 AIM ID. a. Scan the Enter/Exit Programming Mode code. b. Scan the GS1-128 AIM ID=Disable code. c. Scan the Enter/Exit Programming Mode code.

Gryphon™ Family

Datalogic https://www.datalogic.com > marketlit > manuals PDF settings before scanning the ENTER/EXIT barcode a second time, which will then accept your changes, exit Programming Mode and return the reader to normal ...

• QuickScan™ Quick Reference Guide

  https://www.datalogic.com > marketlit > manuals PDF ?crit de la part de Datalogic Scanning, Inc. ou celui de ses filiales ou de ses ... Etat de veille/suspension USB d?sactiv?, entr?e en veille = 0.6 sec.

• PowerScan PBT7100 Cordless Product Reference Guide

  https://www.datalogic.com > marketlit > manuals PDF ENTER/EXIT PROGRAMMING MODE. Double Read Timeout = 0.5 Second. Double Read Timeout = 0.6 Second. Double Read Timeout = 0.7 Second. Double Read Timeout = 0.8 ...

• QuickScanTM Lite QW2100

  https://cdn.datalogic.com > Download PDF ENTER/EXIT PROGRAMMING MODE. Double Read Timeout - continued. $CSNDR32?. Double Read Timeout = 0.5 Second. $CSNDR3C?. Double Read Timeout = 0.6 Second.

My Nelco Sierra 234F stitch length dial was stuck. Turns out it's pretty easy to repair if you are handy with tools. Remove top of the machine. Remove set screw holding stitch length mechanism to body about half-way down inside. I loosened the screw and used a magnet to retrieve the screw and washer. Gently pull mechanism out the front, jiggle a bit to disengage rear cylinder from lever and pin inside body. When out remove two screws holding rear cylinder to mechanism and remove, note that the opening in the cylinder should be up when the dial is set to "button hole." Remove the small snap ring holding the reverse button push rod and spring and pull it out. Remove snap ring holding outer cylinder onto inner cylinder...this probably requires a snap-ring removal tool. Work the outer cylinder free from the inner cylinder by using lubricant (maybe let it sit over night), twisting with a wrench, whatever it takes. The problem is that the oil/grease between the two cylinders has dried out and become sticky. Once the outer cylinder is off clean everything and verify the cylinders turn freely when assembled. Lightly file the cylinders smooth if you gouged them when taking them apart. Lubricate with oil or light grease, reassemble and reinstall the snap ring. Reinstall reverse button push rod, spring and small snap ring. Reinstall rear cylinder with the two screws, note orientation of opening in rear cylinder. Installation is a bit tricky, you have to turn and wiggle the mechanism to get the pin on the lever to enter the side opening of the rear cylinder. Lifting the lever and pin mechanism from the top can help by moving the pin rearwards. It took me a few tries. Once it's in orient the set screw hole in the outer cylinder under the set screw opening in the body and reinstall the set screw and washer (I used a magnet to lower the pair into the screw hole). Reinstall cover and you are good to go. If you drop the set screw or washer remove the bottom and retrieve them, or fish them out with a magnet if you can see them.

This is an old thread, but the best google result. Found these inside the tent - after I spent ages looking for them online.

I CAN USE THIS READER IN WINDOWS 10?

The barcode reader is something that the backup software typically uses to identify which tape it is dealing with. So typically your backup software can already natively read the barcode and therefor you don't need any other software. The linked barcode reader is probably for reading a barcode that was provided via a picture (from a scanner or camera). This has nothing to do with the barcode reader that can be part of a tape library. NET UPC Barcode Reader

Reset tbe scanner and again program the scanner for your required configuration.

My personal suggestion would be to go for these repair catalogs. I know this website reliable-store.com that i used to buy them from, and they have online it was very good manual. Go ahead, I bet.

I trust you have seen this FIXYA Link: Datalogic KYMAN reset Questions It deals with a 'hard reset' (that you have already tried) but there is other info in that Link that may be of help to you? IF all else fails here is a Link for repair service (I KNOW ~ I KNOW)... http://www.datalogic.com/eng/products/healthcare-retail-other-solutions/mobile-computers/memor-x3-pd-636.html#service

Try MFG website, or email their customer service or try manualslib.com

Disconnect the power..

Hello, I have the same problem, I found a description how to fix it: http://www.knowledgeonecorp.com/support/faq/FAQ_programf734.htm but I don't have the right software. How did you solve the problem?

You can download them from www.itexperience.net

this is the part for usb cable for Gypron Datalogic-90A052044