Danco Home - Answered Questions & Fixed Issues
The Danco Universal Faucet replacement handle
Get some Lock-tight formula to apply to the screw. Let it dry a few minutes after application. Naturally, after application of the solution, you have tightened the screw to its maximum. Do not be concerned about ever removing the screw as the material will loosens when you apply manual force.
2/7/2018 9:21:23 PM •
Danco Clear...
•
Answered
on Feb 07, 2018
•
463 views
I have a rebuild kit
The issue might be the tub diverter spout. Most such do not seal well. It is a matter of jiggling the spout knob. It should seal better with a little experimenting.
9/4/2017 6:38:14 PM •
Danco Home
•
Answered
on Sep 04, 2017
•
280 views
I installed stem and the valve will not shut cold water off that is running
If your having major issues, I would try to locate the main on/off valves at your water heater and pump/cold water line in the basement. One the water is shut off, I would try to check if there is a proper seal...as required concerning the stem. It's probably on of the old gaskets that was not remove and doubled up. Happened to me. Good luck!
www.youtube.com/watch?v=kM-TxozD-b4
3/1/2015 1:16:45 PM •
Danco Faucet...
•
Answered
on Mar 01, 2015
•
542 views
HOW DO YOU ASSEMBLE AND INSTALL A DANCO 9S-4H/C
Turn off the water supplying the faucet. Now open the faucet. Remove handle by taking off index button and removing screw. You may need to purchase a handle puller, 10-15 dollars, and a stem wrench set. After removing handle, place appropiate sized wrench on stem and turn counter clockwise. Before installing stem, make sure it is in the open position. You may need to use the handle to turn the new stem. Screw in clockwise.
8/11/2014 9:49:43 PM •
Danco Faucet...
•
Answered
on Aug 11, 2014
•
1,824 views
HOW DOES TEFLON TAPE WORK?
Looking into the opening in your pipe, wrap the tape on in a clockwise direction. The smaller the pipe, the less wraps. 1/8" to 3/8" I use 2-3 wraps. 1/2" to 3/4" use 4-5 wraps. Teflon fills any gaps or voids that may occur between the male and female threads.
8/11/2014 9:32:58 PM •
Danco CORP...
•
Answered
on Aug 11, 2014
•
69 views
Valley 3Z-6H/C
Put the large part of the spring into the plastic or rubber washer first, then insert into faucet. I use a little of petrolem jelly for easy instlation.
12/31/2013 5:18:47 PM •
Danco Faucet...
•
Answered
on Dec 31, 2013
•
603 views
I bought a replacement Danko faucet cartridge for
Thae stem you got that said hot/cold were designed to fit old style cross handle faucets. So both hot and cold turned the same way. If the cold side you are replacing turns the opposite direction then you will need to get a cold stem. Danco does make them. Ask the retailer where you purchased the H/C stem. I hope this helps..
5/13/2013 9:48:53 PM •
Danco Faucet...
•
Answered
on May 13, 2013
•
1,400 views
3z-6h/c
change cold cartridge call danco if you can
2/27/2013 11:56:01 AM •
Danco Faucet...
•
Answered
on Feb 27, 2013
•
164 views
I bought a 3h-10h/c but
The same part works for both Hot & Cold sides. Usually preset to work on Hot (counter clockwise on, clockwise off). To set for Cold, simple remove the plastic clip from the top, slide the ring tab off, flip it over and put back on (you can only put it on one way since there's a flat "key" in it matching the stem) Now its set for Cold (CCW of, CW on). HTH
12/25/2013 3:09:04 AM •
Danco Faucet...
•
Answered
on Dec 25, 2013
•
3,337 views
Not finding what you are looking for?