Dacor Ovens - Page 8 - Answered Questions & Fixed Issues
How do you use the
there is usually a button on the front display that says self cleaning
1/2/2011 2:07:28 PM •
Dacor ECS127...
•
Answered
on Jan 02, 2011
•
67 views
Beeping with f1 error code
F1
touch pad / ERC test This simple test will help determine
whether the ERC (Electronic Range Control or Clock) or the touch pad is
defective when F1 error code is present.
Note: Some models
incorporate the touch pad in to the ERC as a single assembly, in which case this
test is not necessary. Simply replace the ERC (Clock).
Warning: If
you feel in any way uncomfortable performing this test or making this repair,
please contact a qualified appliance repair technician.
1. Disconnect
power to the range (unplug the range power cord or turn the power off to the
range at the circuit breaker). It is very important that the power to the range
has been disconnected, so please double check before continuing.
2. Gain
access inside the control panel.
3. Disconnect the touch pad (also called
keypad or membrane switch) ribbon from the ERC.
4. Make sure there are no
lose wires, or anything else that may cause a short when power is turned back
on. Assemble the control panel back the way it was.
5. Turn the power back
on.
6. Wait for at least one hour to see if the F1 code comes back (usually
accompanied by a beeping sound).
7. If F1 comes back, replace the ERC. If it
does not, replace the touch pad.
12/26/2010 11:24:48 PM •
Dacor ECS130...
•
Answered
on Dec 26, 2010
•
741 views
My dacor oven light won't
Sorry to read about your problem, I hope this helps you out.
you have a defective door switch
I tried to help you. Please help me and Rate/Vote on my response. We take the time to answer your question. take the time to rate us.Thanks and good luck
1/12/2011 8:10:50 AM •
Dacor Ovens
•
Answered
on Jan 12, 2011
•
400 views
After oven turned on for normal baking it starts
If you're not hearing the fan turn at its normal speed, it is possible that your fan motor has become stalled. AC motors will often hum or buzz when they can no longer turn but still have power applied to them. This could be due to bad bearings, or a blockage of some sort. It's probably not easy to get to, but if you can hand check the fan it should spin quite freely. Be sure to unplug the unit before messing with the insides, or shut of its circuit breaker if it's a built-in unit.
12/24/2010 2:18:16 AM •
Dacor ECS130...
•
Answered
on Dec 24, 2010
•
269 views
Oven started making a clicking noise after I
F8 means a fault on the door locking switch.
Something may be preventing the door lock from operating properly.
The solution is to have the door lock switch and wiring checked over.
12/13/2010 5:59:05 PM •
Dacor ECS130...
•
Answered
on Dec 13, 2010
•
758 views
After oven turn on
F1 means the system watchdog cicuit has detected a fault.
Try pressing CANCEL for 30 seconds if it continues after that you will probably need a replacement control board.
12/13/2010 2:54:21 PM •
Dacor Ovens
•
Answered
on Dec 13, 2010
•
125 views
What does "PRB 400 (degrees)"
Hi,
PRB stands for Power relay board.
This is a bad error. This means that the power supply board had failed and needs replacement. The cost of replacement would be anywhere between $150 to $300.Unfortunately, this is not a DIY. You need to call a tech on site to replace the same.
Let me know,if needed further assistance.
Hope i helped you.
Thanks for using ' Fixya ' and have a nice day!!
11/26/2010 12:17:11 AM •
Dacor ECS127...
•
Answered
on Nov 26, 2010
•
145 views
The oven keeps blinking F2
F2
Heating mode high temperature
This alarm is activated when the ERC senses a runaway heat condition or when the temperature exceeds "runaway limits". The ERC will beep until the cancel or another function is selected. If the alarm repeats the F2 code check the oven sensor and wiring after first checking for a stuck relay. If alarm goes away verify the oven will complete a clean cycle without any type of failure.
11/25/2010 6:21:50 PM •
Dacor Ovens
•
Answered
on Nov 25, 2010
•
537 views
The oven setting for convection bake stops at 285
I would suspect the thermostat as being bad, but it could be a heat sensor also. Here is a blog that gives general troubleshooting of this problem, and perhaps it will help:
Here's an answer I found on the web from someone that had already changed the temperature sensor:
Gas oven? You need to remove the bottom panel inside the oven and watch the burner cycle. If it's real slow coming back on, this will let temp drop too far inside the oven, which may indicate a bad ignitor.
Could be this, or a sensor, or the thermostat. Sometimes upper limit switches go bad.
I tried to bring up diagrams of your oven, but could find any one the net.
Here's some info on troubleshooting a gas range, and hope it helps:
http://home.howstuffworks.com/how-to-repair-an-oven7.htm
Good luck.
11/25/2010 6:03:38 PM •
Dacor ECS130...
•
Answered
on Nov 25, 2010
•
231 views
How to clean the oven
The inside of the oven can be cleaned with regular soap and water. Dawn works well on built up grease. if you have very stubborn stains easy off makes a low fume oven cleaner, but try hot soapy water first. the outside can be cleaned with any stainless steel cleaner or window cleaner.
My ECS130sch will not
Hi
When the oven does not heat the issue is with the oven temperature sensor that is bad and you need to replace it. You can test the oven temp. sensor for 1100 ohms and replace if the voltmeter reads less than this. Hope this helps...please post back for further assistance.
Daniel
11/18/2010 11:48:44 PM •
Dacor ECS130...
•
Answered
on Nov 18, 2010
•
155 views
What does the F1 mean
Hi, the F1 error code means a problem with the System Watchdog Circuit..
Press "Cancel", if beeping continues after 30 seconds, replace the main control board (also called clock or ERC).
11/17/2010 2:12:24 PM •
Dacor ECS127...
•
Answered
on Nov 17, 2010
•
512 views
Not finding what you are looking for?