D-Link Logo

D-Link Popular Questions, Answers, Tips & Manuals

Do you work here? Claim your company

  • 1K Products
  • 78K Answers
  • 2M Views

Should be able to hook it up to your computer with hard wire and put it in if you don't hook it up that way it won't work

D-Link Computers... | 201 views | 0 helpful votes


Hi, you need to log into your D-link router and then you van change your wifi password. in case you need any help mail me on ajay94503@hotmail.com

D-Link Computers... | 26 views | 0 helpful votes


you have to try turning the hole lot off and restarting it i had this problem with putting mine and same with printers good luck should work

D-Link Computers... | 52 views | 0 helpful votes


Without providing a model number I can't be specific. Usually it is admin, admin or admin and no password.

D-Link Computers... | 39 views | 0 helpful votes


You need to log into the router using either //router, routerlogin.net. or the IP address which is by default, 192.158.1.1 or 192.168.0.1
Default passwords can be found on the companies website, but many use admin and password

D-Link Computers... | 61 views | 0 helpful votes


To Reset d-link Range Extender follow these steps
1. Look at the Back Of Your Extender There Will A Reset Key at the Back.
2. Press The Reset Hole Using Paperclip Or Pen And Hold For Like 30 Second.
3. Now Release The Reset Key and Restart The Range Extender
Read more at
How To Setup And Configure link Range Extender dlinkap local
I hope you will helpful

D-Link Computers... | 83 views | 4 helpful votes


Noone supports Windows XP anymore. I wouldn't count on any driver updates.

D-Link /... | 361 views | 0 helpful votes


Verify that your laptop can connect to the D-Link. Then on the laptop, in the search window enter CMD. In that window enter " ping 8.8.8.8" If you get a response - actually 5, then your likely issue on the D-Link is DHCP settings. Enter "close" to close the black CMD screen.
A response proves that you have Internet access but only to numeric addresses. Use the supplied disk or instruction manual to log into the D-Link and update the settings. If you get no response, go through the full setup procedure on the D-Link.

D-Link... | 297 views | 0 helpful votes


How do I log into my D Link wireless router?
  • Open up a Web browser.
  • Type the address "http://192.168.0.1" or "http://dlinkrouter" (omit the quotes) into the browser's address bar, and then press "Enter."
  • Log in to the D-Link router with the administrator username and password.
  • The default username is Admin and the password is blank (nothing).

D-Link Computers... | 203 views | 0 helpful votes


Please reset the router and also remove the network from the devices and reconnect with the password.
for more visit www.leadingpcfix.com

D-Link... | 331 views | 0 helpful votes


Contact D-link support number 1-888-494-1155 (Toll-free) usa and find instant help by expert D-link technicians.

D-Link DIR-815... | 117 views | 0 helpful votes


Maybe there was a power surge or spike that damaged the router. But if you unplug it and wait a minute or two, then plug it back in, maybe that will reset it. If it is a router, there's usually a small red button on the back, sometimes recessed, that will reset it and that might cure it.

D-Link... | 144 views | 0 helpful votes


Call Printer support phone number 1-888-687-4491 USA Toll-free and find instant support.

D-Link DP-G321... | 123 views | 0 helpful votes


What kind of construction surrounds your router? Weak signal indicates walls reducing signal strength. Try a repeater in weak areas.

D-Link Xtreme N ... | 520 views | 0 helpful votes


Make sure ASUS modelRT-N13U wireless router is turned on then unplug your new router wait about 30 seconds then plug it back in.
It should find your wireless router.
Here is a web site with more trouble shooting advice:
https://www.asus.com/Networking/RTN13U/

Hope this helps

D-Link Dsl-2750b... | 150 views | 0 helpful votes


Yes, time to upgrade your router.

D-Link ADSL2/2+... | 157 views | 0 helpful votes


Why do you use g only? It's slow.

D-Link Computers... | 7,734 views | 0 helpful votes


Try the following in a command prompt (which is opened by clicking the start button and typing cmd):

ipconfig /release
ipconfig /flushdns
ipconfig /renew

This should remove any old IP address your computer had and request a new one from the router.

Best of luck!

D-Link DI... | 61 views | 0 helpful votes


YOU SHOULD FIRST HARD RESET THE MODEM USING A PAPER CLIP WHILE ITS POWERED ON AND RE CONFIGURE ALLOWING THE REMOTE ACCESS PORT TO WORK

D-Link DI-808HV... | 66 views | 0 helpful votes


Do a reset back to factory defaults. Hold the button down in the pin hole for 30 secs.

D-Link Computers... | 39 views | 0 helpful votes

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top D-Link Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Mike

Level 3 Expert

4356 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1165 Answers

Are you a D-Link Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...