D-Link Recent Questions, Troubleshooting Help & Support

you need a cat 5 or better to work fine, and if you have turned mac filter on, please check/add if needed your laptop to the network, best is to use dlink given cd, with has auto-detect devices function inside, then adjust security setting manually

you have to try turning the hole lot off and restarting it i had this problem with putting mine and same with printers good luck should work

Is this the manual you need?

ftp://ftp2.dlink.com/PRODUCTS/DIR-505/REVA/DIR-505_MANUAL_1.00_EN.PDF

If using lan just connect the extender to the router with a lan cable. The extender will no need to setup.

Nortel Contivity will work with the your D-Link router, however its functionality depends on the authentication type (AH will not work), NAT compatibilty mode, and disabling keep alives on the server. Contact your Network Administrator to find out how your VPN is configured. Step 1 Verify that you are using the latest version of firmware on your router. Step 2 Login to the Web Management for your router by entering its IP address (192.168.0.1) in your web browser. The default username is admin, and the password is blank. Step 3 Click the Advanced Tab to access the Virtual Server Settings. There is a list of pre-defined Virtual Server Rules towards the bottom of the page. Find the IPSec Rule. Click the pen and paper icon to edit its settings. Enable the rule, enter the IP address of the computer attempting to connect to the VPN in the Private IP field, then Apply the changes. Step 4 Create a new Virtual Server entry. Name the Virtual Server, "NortelVPN". Enter the IP address of the computer attempting to connect to the VPN in the Private IP field. For the Protocol Type, select Both. Enter 9550 for both the Public and Private Ports. Set the Schedule to always, then Apply the settings. Step 5 Access the Tools Page, then click the Misc button. Disable IPSec Pass-through, then click Apply. If the VPN Server is properly configured to work with clients behind NAT routers you should be able to connect to the VPN.

DSL routers don't need any firmware nor device-drivers.

Hi!

The wizard (link below) will get your wireless up and running in just a few minutes.

Hope this is helpful.
-Steve


DI 524

Without providing a model number I can't be specific. Usually it is admin, admin or admin and no password.

Try going to D-Link website for firmware upgrade to this model, Also make sure u download the the firmware for the version of windows you are using. In order to upgrade, the router must be hard wired that is connected directly to your modem as unit will not upgrade using wireless connection.
Hope this helps you!!

Should be able to hook it up to your computer with hard wire and put it in if you don't hook it up that way it won't work

Hello, You definitely fix this problem with Router Commander. This program was specialy developed to slove D-Link routers problems and was fully tested and compatible with D-Link G604T.

If you want to RECEIVE telephone-calls:

COMCAST ADSL/CABLE modem <---> VONAGE <---> wireless-router

Turn each piece off.
Turn on the COMCAST modem, and wait for its lamps to settle-down to a "steady" pattern.
Turn on the VONAGE router, and wait for its lamps to settle-down to a "steady" pattern.
Turn on the D-link router, and wait for its lamps to settle-down to a "steady" pattern.
Restart the computer that is connected to the D-link router,
and you should have Internet access.

You'll have to login to the router configuration page. First, in Windows Operating System, click on the Start menu, type "cmd" into the search field and press enter.
In the command window that appears, type in "ipconfig/all". If you are on a computer that is connected directly to the router, scroll to the heading that is titled "Ethernet Adapter Local Area Connection". If you are connected wirelessly, scroll to the heading titled "Wireless Adapter Local Area Connection".
Find the "Default Gateway" in the correct section and note it. In your default internet browser, type the Default Gateway address into the address bar and press enter.
You should see a small window come up asking for a username and password. By default the username/password for D-Link routers is admin/admin or admin/blank.
After you successfully login, you can find the section to change the wireless password. Select WPA/WPA2 as the authentication type and enter a passphrase. Be sure to save your changes!
Lastly, to see a list of connected client computers, browse to the status section of the router's configuration page.

If you are facing issue while using Dir 618 configure as a bridge router then i recommend you to once read this blog to get understand the proper concept to use it : https://www.routertechnicalsupportnumbers.com/blog/fix-invalid-wi-fi-ip-configuration-issue-on-windows-10/

Hi,

Since the router has reset itself, you can login it very easy. Go your web brower and in the space for the url address type 192.168.0.1 It will then bring up a screen for user name and password. The user name is admin and the password is left blank. Once you enter that information your logged in.

Good Luck

Mark

check whether they are using automatic IP addressing . it may be they are using the same IP in static mode so that one won't connect.

disable the adapter in the change adapter settings page. Then re enable it and try it. You can also remove the driver from device manager and reboot, windows will automatically reinstall the drive and it may work. USe the troubleshooting app to fix or detect the issue. If the connection show it has internet but you can't reach a page, try another browser.

You need to log into the router using either //router, routerlogin.net. or the IP address which is by default, 192.158.1.1 or 192.168.0.1
Default passwords can be found on the companies website, but many use admin and password

Hi,

Did have the same problem, but I was able to find a support link, which D-Link's support for Australia and New Zealand.

Please refer to the link below. This provides driver for Vista 32, 64 bit and Windows