Cisco ASA - Recent Questions, Troubleshooting & Support - Page 5

http://www.netcplus.com/ncfonline_routers.html

Please view the above web link may be it help your issue

De ce nu pot Dwnloada???

Hello there, you need to check this out

Regards

are you using hyper terminal? if you are using another program, switch to hyperterminal and reboot (if possible after saving config) with the cable connected. See if anything at all comes up on the screen.

can you try lower encryption levels on each device and see if that helps? sometimes it is neccesary between Cisco and other devices.

1. Change your PCs default gateway to your firewalls' internal IP

2. configure the nameservers on your ASA

Then internet will work fine.

Hi, the Cisco ASA 5505 is the base model, and URL filtering is not available on this model. The first model that allows URL filtering is the 5510, and every model above that. You can view the models and features here:

http://www.cisco.com/en/US/products/ps6120/prod_models_comparison.html

If you are going for factory reset use the following commands

asa>enable
asa#write erase
asa#reload

Dont save the configuration when it prompts for it.

if you want to restore the configuration from the backup

1. You need to have a TFTP server
2. Locate the config file on your TFTP server
3. TFTP server should be reachable from ASA

then

asa#copy tftp flash

give the tftp server ip address
give the configuration file name (as exactly on the TFTP server)

reload

Yes. The firewall will restart. Just be sure to save your running config to memory before turning off. For that you must issue the command: write memory.

Best Regards,
T

You can only do active/active if you're using multiple contexts. Active/active can give you some extra performance for your $ since you can pass traffic through both ASAs. Compare this to active/standby where the standby unit passes no traffic.

If you're pushing the 5510's to 80% capacity each in active/active mode, then you have one fail, now the one single ASA is oversubscribed. The oversubscription could cause connectivity issues that defeat the purpose of failover in the first place.

In the spirit of reliability go with active/standby. Seeing that you have two active core switches that would be pushing all of their traffic through a single 5510 in this case....it may be too much active/active may be the better solution.

configure the SNMP traps and view the logs hope it will help you to solve this problem.

you can feel free to call to this mobile number ill help u 09620077956.cuz we are the solution providers.

A conflict in the IP address, resolve it

Hi the documentation lists it in detail if you donot have the docs then access the same on Cisco web site it is free

This is the best doc. I can find to help you with your problem.
https://www.cisco.com/en/US/docs/security/asa/asa70/quick/guide/70_ASAqk.html#wp46243


Please let me know if it helps...
Tim

Hello kuniksh,

Look at the below link for all configurations
http://www.akadia.com/services/cisco_router_firewall.html


Do rate this solution!!!!

You can do this, For your ref i hv given you a link

http://channel9.msdn.com/forums/9GuyAroundTheWorld/251722-Cisco-Pix-to-Windows-Vista-Native-Client-Using-L2TP-IPSec/

If you can't get the manament working initially I suggest the following

Setup a console connection
Type "enable" and press enter to access priveleged exec mode on the ASA
Type "config terminal" and press enter to access configuration mode
Type "configure factory-default" and press enter to load default settings.
Assign a static IP to your PC of 192.168.1.5 and try to browse to https://192.168.1.1 (PC is plugged into management interface)

You should be prompted to begin using ASDM

Voila un link pour un bon simulateur:
http://networksims.com/pix.html

Check for an IP conflict. How are you assigning the IP address on the workstations? If one of them happened to have the same ip address as the ip on the vlan1 on the ASA for example, you would have that exact issue.

Let me know how things go.