Chrysler Recent Questions, Troubleshooting Help & Support

Question edited for clarity, add maker. Question moved to model category. 'Fire' and 'Start' and normally the same thing, do you mean 'crank no start' or do you mean you have verified you have a spark? The fuel pump can be checked for operation by listening for it, and it can also be checked from fuel pressure by connecting a gauge at the fuel rail. Did you buy OEM quality or a cheap one from Mexico or China? You could also check the operation of the fuel pump relay. https://www.google.com/search?q=2003+chrysler+town+and+country+fuel+pump+relay+location Various ideas here https://www.google.com/search?q=2003+Chrysler+Town+and+Country+3.8.+It+will+fire+but+will+not+start

There are two fuse boxes on your car. One under the hood of your car generaly on the drivers side of the car near the fender. Look for a black plastic box. open it and check the guide inside the cover. The other fuse box is inside your car in the edge of your dash panel.

Here is a link to give you all Chrysler Firing Orders, it also shows you ththe cylinder #'s : http://www.aa1car.com/library/chrysler_firing_orders.htm

-Check to see if any fuse that supply power to it..? If it is then is the fuse blown or not. If it's blown then replace with new one. Good luck Mai

It probably has it's own fuse. some times kids put things in the lighter sockets or stuff just falls in there. Pennies are real popular for causing that. Either that or a higher amp device was plugged in the socket and blew the fuse.

under the hood under a black box or in the door or under the dash but more than likely under the hood

https://www.300cforums.com/threads/where-is-the-tcm-located.280652/ The TCM is located behind the trim panel, below and to the left of your steering column. If you have a factory amplifier, the TCM is the black box to the right of the amp. https://www.google.com/search?q=2016+Chrysler+300S.+Where+is+the+TCM+located //

Yes, you release the Neutral Switch manually. It is actually a Plymouth Reliant but made by Chrysler. https://www.google.com/search?q=1989+Plymouth+Reliant https://www.google.com/search?q=how+to+get+an+automatic+car+into+neutral+without+a+key Not much specifically for that vehicle, but all have a way to do it. https://www.google.com/search?q=1989+Chrysler+Reliant+into+Neutral+without+key ..

Did you find an answer to this? We have also located this part. It appears to be nothing more than a ballast/weight that was factory installed. But it is loose and clunky for sure. One on the frame rail and one inside the right fender liner.

Question edited for clarity and add maker. Question moved to model category. Various solutions here https://www.google.com/search?q=2007+Chrysler+Town+and+Country+3.3%2C+no+reverse ..

The heated seats are powered by two fuses in the TIPM module under the hood. Fuse 31 & Fuse 33. The hazards are on a separate fuse

Signal timing is that fast the amount of wire you remove shouldn't really affect it. Length is more of an issue when the wires are too short to reach the crank sensor, Too close to a moving part or pulled too tight and has sharp, tight bends in it. You can buy a set of 'Keys' that will allow you to release the actual pins from inside the connector block. You then simply push them, (in the correct order), into the replacement one. I think they're called 'Terminal Keys'.

it is in limp mode to protect the engine and transmission run the fault codes and fix what is found

Question edited for clarity and toss in a load of CAPS. Question moved to model category. Apparently it does and according to one of the videos, a pro grade scan tool is involved. https://www.google.com/search?q=Does+the+crankshaft+position+sensor+on+my+Chrysler+LHS%2C+need+a+relearn+procedure ..

check o2 sensor. may have a short or damage

run a scan for the trouble code

To change the idle speed on a 2.4 pt cruiser engine, on the front side of the throttle body towards the intake manifold, there is a tiny star screw ( one with the point sticking up in the middle ) that you can turn to raise and it lower the idle speed with.

Please don't type in all CAPS, it is a considered SHOUTING and harder to read. This website gets 11 million viewers per year and a great number come here to spam and harvest person data like email addresses, so using an email address Bluesman2 at shaw.ca as your published name is not a good idea! 'bluesman' would have been fine as we never email answers. Switch is at the top of the brake pedal. Remove the panel under the dash for access.

Brake light switch location??? - CrossfireForum

Crossfire Forum https://www.crossfireforum.org > ... > Crossfire Roadster ..

Question edited for clarity and correct spelling of model . Question moved to model category. some ideas here in the lower link, but the best way is to call a local auto electrician. A pro grade scan tool computer can diagnose in about 20 minutes. The computer can instruct shift solenoids to work and verify that they did. https://www.google.com/search?q=mobile+auto+electrician+near+me https://www.google.com/search?q=2007+Chrysler+Pacifica+has+Reverse+but+no+Drive ..

Sounds like you need to have the ignition programmed to your VIN #