Chevrolet Logo

Chevrolet Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 2K Products
  • 578K Answers
  • 8M Views

No. The most common problem with the low sensor light is the switch which is located in the radiator just below the filler neck. First make sure that the radiator is full. With the cap off, start the engine and then add coolant to the radiator. There are two bleed valves in the system. One by the thermostat area and the other by the by-pass hose close to the water pump. Be sure all the air is out of the system. The low coolant sensor gets dirty and causes this problem.

1993 Chevrolet... | Answered on Mar 24, 2019


Welcome to Fixya

Raise the front of the car then slide under the driver's side of the car and locate the starter on the engine where it meets the bell housing. Unplug the "S" connector from the terminal on the starter and lay it aside. Remove the nut from the "B" terminal with a wrench, then remove the battery cable from the starter. Locate the mounting bolts and loosen it. Slide the new starter then tighten the bolts.

Please click here if you need further assistance.

Thanks

If you need further help, reach me via phone at https://www.6ya.com/expert/elixirjose_00375ea24bd8141b

2006 Chevrolet... | Answered on Mar 24, 2019


Locate the IP to body harness connector, which may be located in and around the left hand kick panel area or inside the IP. Check to see if there is a water leak into the area and repair as necessary.

2008 Chevrolet... | Answered on Mar 23, 2019


Try instrument panel fuse 17, AuxiliaryPower Rear. ...The instrument panel fuse block is located on the passenger side panel of the center console. To access the fuses, open the fuse panel door from the passenger side by pulling it out.

2016 Chevrolet... | Answered on Mar 23, 2019


Need help programming a key fob for a 2005 Chevrolet Cobalt

2005 Chevrolet... | Answered on Mar 23, 2019


Tip & How-To about Cars & Trucks
Resetting a Vehicle Anti-Theft System
This is how you reset an anti theft system if you have the anti-theft light on, or your car is cranking, but you have no spark.

Doing a full reset of the anti-theft system.

Disconnect both battery leads for at least two hours.
Hold the negative and positive leads together for 5 minutes to fully discharge any power.
Put the key in the ignition, but not turned on. VERY IMPORTANT!
Connect the positive lead.
Connect the negative lead in one swift movement.
Wait 15 minutes for the system to fully reset.
Posted by Andrew... on Jan 14, 2018

Resetting Vehicle Anti Theft System

2003 Chevrolet... | Answered on Mar 23, 2019


Look in resevoir check level Check power steering pipes under hood look for fluid leaks

2008 Chevrolet... | Answered on Mar 22, 2019


engine temp sensor or its connector is bad.

1998 Chevrolet... | Answered on Mar 22, 2019


There should be a section in the owners manual to tell you how. Most Chevrolet have a release lever under the dash right above the e brake pedal.

Chevrolet Malibu... | Answered on Mar 21, 2019


There could be something in the oil that is blocking oil flow in the galleries. Have you checked the condition of the oil for any foreign substances? It could also have something to do with the oil pump operation, but I think it unlikely.

Chevrolet... | Answered on Mar 21, 2019


buy a service manual and fix it

Chevrolet S 10... | Answered on Mar 21, 2019


Ask Google . 1988 and up will be the same.

Chevrolet Cars &... | Answered on Mar 21, 2019


do you have an aux port on the front of the radio? otherwise the aux looks like it should work, but, it doesn't

Chevrolet... | Answered on Mar 21, 2019


this is the security system light flashing to let you know it is active

2005 Chevrolet... | Answered on Mar 21, 2019


buy a manual an look it up. Your going to need the diagnostic steps any way . $20 some bucks for repair info for a year .
http://www.alldatadiy.com

Chevrolet Malibu... | Answered on Mar 21, 2019


This will not prevent the car from starting - will cause ABS light, traction control light (if equipped) and maybe weird low speed braking. Usually the fault of the lights is a bad wheel bearing/hub very common.

The EBCM (Electronic Brake Control Module) is mounted to the BPMV (Brake Pressure Modulator Valve) located at the left front (lower) engine compartment.

It looks like a (thick) flat black box.

2005 Chevrolet... | Answered on Mar 21, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Popular Products

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

84540 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Brad Brown

Level 3 Expert

18031 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...