Cardiozone Exercise & Fitness - Recent Questions, Troubleshooting & Support

Hello again Having typed everything below the dotted lines for the last 30 minutes, I found this. It has a magnetic speed sensor on the pulley https://www.justanswer.com/fitness-equipment/2srkz-just-moved-cardiozone-elite-max-hr-treadmill.html ============================================== Here is the parts diagram and it shows no speed sensor and all parts are unavailable. https://www.fitnessrepairparts.com/equipment/Select/7631/CardioZone/CZE-Elite-Plus-HRT Parts Diagram closeup https://www.fitnessrepairparts.com/equipment/7631/diagrams/7403 That is contradicted here, but my view is that they are guessing because the parts diagram shows no sensor and if it was there and a part of the management system and expected to fail, it would be. There is a picture of of two sensors from Amazon and eBay, one is a Hall Effect Sensor, and the other is a Magnetic sensor. If it has them, you wouldn't be able to miss them and they would be connected to Part 17 - Controller. https://www.google.com/search?q=cardiozone+elite+plus+hr+t+treadmill+sensor+replacement Generic Treadmill Sensors Treadmill RPM Speed Sensor - Replacement for Pacemaster Bronze, Pro, Plus, Plus 2, Elite, & Select Treadmill $21.14 Amazon CA High Quality Treadmill Magnetic Sensor Speed Sensor For Running $12.89 eBay Free shipping ..

Try pressing the Mode button again until the error message goes, or disconnect from the mains or remove batteries to reset. How do I fix E7 error on treadmill? E6 or E7

1. Turn the power OFF, wait 5-seconds and turn back ON.
2. Get into test mode and enter through the I/O testing step. ...
3. Once the unit is in the mid-level position, power the treadmill off for 5-seconds and then power it back ON.
4. Start the treadmill.

https://www.google.com/search?q=cardiozone+treadmill+e7+error

Use a non alcohol based silicon spray or liquid. The WD40 brand make the 3 in 1 silicone spray and it’s good for all non waxed running belts. Just make sure you get the spray in the middle of the belt. (Underneath of course) watch a YouTube video if unsure.

Nice blog. Thanks for sharing this valuable information. <a href="https://sportsindeed.com/excercise-fitness/treadmills.html">Treadmill Dealer in Chandigarh</a> <a href="https://sportsindeed.com/excercise-fitness/treadmills.html">Treadmill Dealer in Mohali</a> <a href="https://sportsindeed.com/excercise-fitness/treadmills.html">Treadmill Dealer in Panchkula</a> <a href="https://sportsindeed.com/excercise-fitness/treadmills.html">Buy Treadmill in Chandigarh</a>

1st take side rails off front hood .you have afront roller and a back roller. for the front take out the two or one bolts holding the the roller in placenow the back roller take out the bolts that hold the roller in place . now on the deck there is 3or 4 screwson each side holding the deck in place. slide w/ belt off put on new deck.install screws, rollers ,bolts.. now center w/belt and adjust tention on w/belt

Your problem might be that a magnet has fallen off. Here's an illustrated guide which should make fixing it easy: http://fixmytreadmill.blogspot.com/2010/10/how-to-fix-treadmill-e1-error.html

Good luck.

Your controller is shot. Replace your controller

This could be cused by the the display cover you touch to control the functions pressing on the touch switch array just under it. Carefully remove this. it is held on by adhesive and see if the symptom goes away. If it does, look for any dents on the cover. I have worked with these type of switches for nearly 20 years and they can be problematic. The other possibility is the mechanical switches you use to increase/decrease speed or tilt. They plug in seperately and you can disconnect them to see if they are causing the problem.

This usually means a faulty LCB or motor.The fact it has not been used much doesn't matter. It is 7 years old. Usually you can not see faulty parts on the LCB. I do think if you really want the answer call a treadmill repairer . If you don't know what you are doing it can be dangerous.