Even though the power is off, if the power cord is connected there is power going through the power supply.. What you are smelling is most likely the filter capacitors getting ready to fail
i kindly advice you restart the camera ,it may fix the problem,.Also ensure on the camera's buttons or around the scroll wheel there is no dust .If it persist try to reset factory the camera
Description: Center Thermistor low temperature detection at printing
In the period from printing to last rotation, Main Thermistor 2 detected a temperature of 80 deg C or lower for more than 1 second.
Remedy: Fixing Assembly error, Fixing temperature detection error 1. Check failure between the DC Controller PCB (UN09/ J12) and the Fixing Assembly (UN37/ J123, UN13/ J13) (trapped cable, open circuit, connector disconnection). -> Replace the part in the case of trapped cable/open circuit 2. Replace the Fixing Assembly 3. Replace the DC Controller PCB (UN09) NOTE: After performing the above remedy work, go through the following to clear the error: COPIER > FUNCTION > CLEAR > ERR
The Canon imageRUNNER ADVANCE DX C3835i error code E000202-0010 indicates a problem with the fixing film rotation. Here's some information about the potential causes and steps you can take to address the issue:
Fixing Film: The fixing film is a component within the fixing assembly responsible for transferring heat to the paper during the printing process. It's possible that the fixing film has become damaged, worn out, or needs replacement. Inspect the fixing film for any visible signs of damage, such as tears or wear. If necessary, contact Canon customer support or a qualified technician for assistance with replacing the fixing film.
Fixing Assembly: The error code can also be caused by a malfunction in the fixing assembly itself. The fixing assembly consists of various components, including the fixing film, upper roller, lower roller, and temperature sensors. If there is a problem with any of these components, it can trigger the E000202-0010 error code. In such cases, it is recommended to contact Canon customer support or a qualified technician for further diagnosis and repair.
Power Cycle: Sometimes, a simple power cycle can help resolve temporary issues. Turn off the printer, unplug it from the power source, and wait for a few minutes. Then, plug it back in and power it on again to see if the error clears. If the error persists after the power cycle, further troubleshooting or repair steps may be necessary.
It's important to note that the E000202-0010 error code is specific to Canon imageRUNNER ADVANCE printers, and the exact steps or recommendations may vary depending on the specific model and configuration of your printer. Consult the printer's user manual or contact Canon's customer support for more accurate and detailed instructions tailored to your specific printer model.
In general Compact Flash Cards have to be formatted within the camera that is using them as they use a format proprietary to that camera. Also there are size limits on cards. If your camera will only take 16 Mb cards and you put a 32 Mb card in, it will not read it. It sees it as 'No Card Present'.
I think the other answer is an AI Answer Bot.
Here are some actions you can take to investigate and solve the issue.
a) Double-check to make sure the toner catritdge it is inserted properly and firmly into the printer.
b)Considering that you mentioned replacing the fuser unit, make sure it was placed properly.
c) thoroughly clean the printer's inside, including the rollers and paper path.
The error code E00807-0001 on a Canon imageRUNNER Advance C5235 indicates a problem with the fixing assembly, which is responsible for fusing the toner onto the paper. Here are some steps you can try to troubleshoot and resolve the issue:
Power Cycle: Turn off the printer using the main power switch, which is usually located on the side or rear of the machine. Wait for a few minutes, then turn the power back on. This can sometimes clear temporary errors.
Check for Paper Jams: Open the printer's front cover and check for any paper jams or obstructions in the paper path, especially around the fixing assembly area. If you find any paper jams, carefully remove the paper following the manufacturer's instructions.
Inspect the Fixing Assembly: The fixing assembly is located inside the printer, typically behind the front cover or access panel. Check for any visible signs of damage, such as broken parts or loose connections. Ensure that the fixing unit is properly seated and securely in place.
Reset the Fixing Assembly: If there are no visible issues with the fixing assembly, try resetting it. Open the front cover and locate the green handle or lever associated with the fixing assembly. Move it back and forth a few times to ensure it is properly engaged.
Contact Canon Support: If the error persists after attempting the above steps, it is recommended to contact Canon's customer support or a qualified technician for further assistance. They will have access to specific troubleshooting steps and can provide guidance based on their knowledge of the Canon imageRUNNER Advance C5235 model.
When contacting support, be sure to provide them with the specific error code and a description of the issue you're experiencing. This will help them in diagnosing the problem more accurately and providing appropriate solutions.
Please note that the error codes and troubleshooting steps may vary depending on the specific model and configuration of your Canon imageRUNNER Advance C5235 printer. Always consult the printer's user manual or contact Canon's customer support for model-specific instructions and recommendations.
It needs to go in for cleaning and service. It is a vintage recorder and the rubber feed capstans are probably sticky and need replacing.
It is a known issue.
https://www.google.com/search?q=Canon+XL1S+eats+tapes
..
