Canon Office Equipment & Supplies - Page 9 - Recent Questions, Troubleshooting & Support

Once you get the warnings you will normally get lots more prints before it actually runs out. Printer Properties will tell you the Ink levels. I used to use exclusively Can original cartridges, but fed up of paying the exorbitant prices, I bought two full sets of cartridges off amazon, 14 cartridges in total for $32. They are working great.

Perform a hard reset of printer electronics to factory defaults and/or reinstall the driver. If still bogus contact Canon tech services but you may need a new printer. if nothing works.

404 error = question has been deleted [ problem has existed with question or was spammed ]

The E000073-0001 error code on the Canon ImagePRESS C1 photocopier is related to a problem with the temperature sensor in the fuser unit. Here are some steps you can take to try to resolve this issue:

1. Turn off the copier and unplug it from the power source. Allow it to cool down for a few minutes.
2. Check the fuser unit for any visible signs of damage, such as wear or burn marks.
3. Check the temperature sensor and its wiring for any signs of damage, such as frayed wires or broken connections.
4. Reconnect any loose or disconnected wiring and ensure that the fuser unit is properly seated and connected.
5. Power on the copier and see if the error code has cleared. If it hasn't, you may need to replace the fuser unit or the temperature sensor.

If you are not comfortable performing these steps or if the error code persists after attempting to troubleshoot the issue, it is recommended that you contact a professional technician or service provider who is experienced in repairing Canon photocopiers. They will be able to diagnose and fix the problem.

Error code 744-3030 on a Canon IR 4570 indicates a problem with the toner hopper. Here are some steps you can take to try to resolve the issue:

1. Turn off the printer: Turn off the printer and unplug it from the power source. Wait for a few minutes and then plug it back in and turn it on.
2. Check the toner: Open the toner hopper and check to make sure there is toner inside. If the toner is low, refill it.
3. Check the toner hopper motor: The toner hopper motor may be malfunctioning, causing the error code. Check the motor to see if it is working properly. If it is not, it may need to be replaced.
4. Check the toner hopper sensor: The toner hopper sensor may be dirty or malfunctioning, causing the error code. Clean the sensor and make sure it is working properly. If it is not, it may need to be replaced.
5. Reset the printer: Reset the printer to clear any error codes. To do this, turn off the printer, press and hold the "1" and "9" buttons, and turn the printer back on. Release the buttons when the display shows "Initializing."

If the above steps do not resolve the issue, it may be necessary to contact a professional technician or Canon support for further assistance. They can help diagnose and fix the problem safely and effectively

It sounds like you may be experiencing a mechanical issue with the Canon Imageprograf Pro-2100. The error code EC1C-2036 is related to the lower drive nipe arm unit, which is responsible for moving the different components of the printer in order to produce prints. This error can be caused by foreign objects becoming stuck in the unit, or by the unit itself becoming worn out or damaged. To resolve the issue, you will need to first inspect the unit for any foreign objects, and if none are found, then you will need to replace the unit. If you are unable to locate the part or don't feel comfortable attempting a repair, then it is recommended that you contact a professional for assistance.

Question edited for a lot more clarity. Question moved to model category.

Canon iR2525 - Error Code: E110-0001 - Printcopy.info

https://printcopy.info > brand=Canon > model=iR2525 Code: E110-0001; Description: Failure of the Scanner Motor (M21) The Scanner Motor (M21) speed lock signal does not indicate a locked state a specific ...

The best way to reset your Canon printer is to find and hold the reset button on your printer. This usually consists of a small pinhole or recessed button located on the back or side of the printer, depending on the model. Press and hold the button for a few seconds until the printer resets itself.

Error code CANON iR4570/ iR3570 / iR2870 / iR2270 ' Tjah Semrawut Blog (wordpress.com)

errore SC544

https://www.google.com/search?q=CANON+IMAGERUNNER+ADVANCE+2030+error+code+E000196-1BFF ..

Try installing the Windows 10 x64 driver for the Pixma MP560 from https://canoncanada.custhelp.com/app/browse/a_status/published/channelRecordID/DRIVERS_AND_SOFTWARE/pageSize/25/productCategoryAnsList/RN_PRODUCT_1801%3ARN_CATEGORY_2652%3ARN_CATEGORY_318/productRecordID/RN_PRODUCT_1801/truncate/200/type/browse/session/L3RpbWUvMTY3NjI0NTQxMC9nZW4vMTY3NjI0NTQxMC9zaWQvZlVzazJtd0U3ZTZIWmN2bllCZnN1UVdGJTdFbTBINENOWnI5bl9FN2cxTVdWRHVSRkt4b2xlS1hDYUJneUNjRGh1c192Nk9kOEhiMTdId3FLX3BCdDhtZGNLX3VrbGpIczNnYkg2dHpFS3V5dGhWa0ZEWlNOU1RQb1ElMjElMjE%3D . Use the drop-down menu to specifically choose that version. Most Windows 10 64-bit signed drivers work under Windows 11. (At least one person had to download the file twice.) I hope this helps. Cindy Wells

ENGLISH only on Fixya please I HAVE A HARDWARE ERROR 03130031 - 2F17 I HAVE A HARDWARE ERROR 03130031 - 2F17, IN A CANON iPF8000 PLOTTER, COULD YOU TELL ME WHAT IT IS ABOUT AND HOW TO SOLVE IT?

Canon imagePROGRAF iPF Error Code 03130031-2F17

https://proprintingsystems.com > canon-imageprograf-i... The 2F17 error is a Platen fan lock detection error. Your Canon imagePROGRAF printer will show this error when the lock signal has been supplied ...

Turn the power off at the wall and remove the plug. Remove the toner cartridge and tap it on one end and then on the other. Tap the cartridge horizontally to settle the toner and then replace the cartridge in the machine. Plug back in and try again. The toner may in fact be empty, but doing that will usually give you some extra time and copies. Worst Scenario in the video! https://www.google.com/search?q=Canon+ir+3300+print+out+is+faint

Question edited for clarity.

How to Fix Error Support Code 5b02 on Canon Printers

https://canonservice.net > How to Error 5b02 is an alarm warning for errors that occur on the printer, we have to do a reset so that the printer returns to its initial settings and Error ...

Take a bottle of Isopropyl Alcohol and clean the electrical contacts on the drum and also the contacts on the machine. Bad connection. Videos as well.

I'am making over $15k a month working online. I kept seeing how some people are able to earn a lot of money online, so I decided to look into it. I had luck to stumble upon something that totally changed my life. After 2 months of searching, last month I received a paycheck for $15376 for just working on the laptop for a few hours weekly. I was amazed how easy it was after I tried the copy below web...www.join.hiring9.com

In the link https://www.google.com/search?q=Canon+C3226i++error+code+E000202-0010 ..

that is usually a scanner error, the unit will need to be returned to canon or serviced.