Canon Cameras - Page 4 - Recent Questions, Troubleshooting & Support

Question edited for clarity. Your memory card is too big and beyond the capabilities of the camera. 512Mb is recommended. Page 34 of the manual http://gdlp01.c-wss.com/gds/8/0900001188/01/PSA540_530CUGad-EN.pdf ..

Bruce, Try these steps:1. Set camera to manual2. Set shutter to 1/603. Set aperture to F5.64. ASA/ISO 2005. 550EX on hotshoe6. Do not set on slave or master7. Turn on flashDisplay must shows, ETTL.If that doesn't work, you have to use the flash on manual.Some of this model will not work fully on ATG Canon EOS-1D C, ATG Canon EOS-1D X IR, Canon EOS-1D X/60D/T4i because this flash is over 20 years old.Unless you would want it to be modified by me.But that can be costly when you can get the 580EX II for less than $425.00 [email protected]

If you had the ATG Gold MG8k Flash Kim X3, then your 430EX II or 580EX II can transforms into wireless radio ATG ETTL II. If you are using the outdated wireless IR ETTL with a 580EX II as a Master. Then you have to set the Slave (ATG/580EX II/430EX II) body facing close to the Master. [email protected]

Question edited for clarity. Yes it can, although it won't work by metering the light that is hitting the CMOS sensor. You will use it in manual mode.

How old is the battery? They will only take a certain number of charge and discharge cycles. When worn out, they will charge, but fail very quickly and always in the middle of use. https://www.walmart.ca/en/ip/2x-Pack-Canon-EOS-Rebel-XS-Battery-Charger-Replacement-for-Canon-LP-E5-Digital-Camera-Battery-and-Charger-1200mAh-7-4V-Lithium-Ion/PRD1R0BZPXKL7K5 https://www.google.com/search?q=canon+eos+rebel+xs+battery ..

Connection to body or battery voltage.

Yes it is possible that the battery is getting weak. Or the button which is of course a switch needs cleaning with electrical contact spray.

There must be either weakness in the contacts or the contacts are dirty. https://www.google.com/search?q=Canon+Powershot+a1100+will+only+switch+on+and+stay+on+if+I+press+the+battery+cover ..

Question edited for clarity. Question moved to Pixma MX410. Unplug the machine. Remove paper trays. Open all the doors, slide the carrier and remove the cartridges' and print head. Use a flashlight and look for a small piece of torn paper. Clean the rubber feed roller with a soapy cloth. Replace the paper with new from an unopened pack as what you have may be damp. Put it all back together and try again.

The best way to download pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the computer or connected via USB or FireWire). This is likely to be faster than connecting the camera to the computer, and won't run down your camera's batteries.

Once the card is plugged in, it will appear to your computer as a removable drive. You can use the operating system's drag&drop facility to copy pictures from the card to the computer's hard drive, the same way you copy any other files. Or you can use any photo cataloging program.

Try Picassa. All you need to do is to make some basic correction. very very minimum that you dont even know that there is a change. save the photo back into a different location. You will see a change in the pic size.

Alternatively, google for Digital Photo Resizer. I used a trial version for sometime and it helped.

- Ranjit
[email protected]

Question edited for clarity. Question move from Computers to Canon Camera. There is no 'Reset' only Reset Camera to Defaults. The most likely reason is completely flat batteries. https://www.manualslib.com/manual/355860/Canon-Ixus-80-Is.html?page=177 ..

Consider NOT connecting your camera to your computer.

The best way to download pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the computer or connected via USB or FireWire). This is likely to be faster than connecting the camera to the computer, and won't run down your camera's batteries.

Once the card is plugged in, it will appear to your computer as a removable drive. You can use the operating system's drag&drop facility to copy pictures from the card to the computer's hard drive. Or you can use any photo cataloging program.

Hello, Check the status of the printer at Control Panel. Set it to online if it's shown as offline. If this doesn't fix the problem, check whether installing the vista driver available at your printer manufacturer's website helps. Step 1: a. Click Start, go to Control Panel and select Hardware and Sound. b. Click Printer. c. If the Printer is offline, it shows "Offline" status. If the Printer is online it shows "Ready". d. If the Printer is offline, set it to online. e. Right-click on the printer and select "Use Printer Online". f. The display should change to ready when the printer is set to online. Step 2: If still you are facing issues, then update the printer driver. This should fix the problem. For further precise instructions, please let me know the Operating Systems installed on the Computer. Hope this helps..

Question edited to add full make and model. Question moved from Dishwashers to Canon PowerShot A630. https://www.google.com/search?q=take+the+back+off+the+screen+of+A630+camera Personally, I would send it to Canon for professional service. It may just be a problem with insufficient battery milliamps. https://www.google.com/search?q=A630+camera+E24+Error+Code ..

Try another charging cord. The camera charging cords are just as bad as the phone cords. They just go bad quickly.

need to install VLC or media player classic Ninite Install or Update Multiple Apps at Once

The external flash mount (hot shoe) has a small sliver of metal which when the external flash gun is slid on pushes it down to tell the body to not use the pop-up flash and some times the sliver doesn't return fully up to contact the underside of the hotshoe

how to reset the error signal 5 for canon ip4840

Maybe lens needs adjustment. The info on this page may help. Copy and paste this link for more info.


http://www.fixya.com/PostAnswer.aspx?thid=1841738&prdid=447928&ctgid=67