Buick Logo

Buick Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 379 Products
  • 171K Answers
  • 3M Views

Try YouTube:

https://youtu.be/nzaNHbVZOnQ

Buick Cars &... | Answered 7 hours ago


The fact that both are out points to the headlight switch or connector. There's a separate fuse for tail lights but the head and park (front) lights are powered by a fuse link that controls a lot of other stuff you would notice. Reach under the dash and put your hand on the light switch, feel for the wires then feel the other side of the switch for a small button then pull the switch all the way on, depress the button and pull the switch knob and shaft the rest of the way out, now remove the special screw and the switch. I hope this helps. Take care. If you need more help from me use the testimonial button and it will show up in my email.

Buick Cars &... | Answered Yesterday


I DON'T KNOW. BEST GUESS IS IT IS SPARK SOURCE.
CONSIDER TESTING COIL WIRE [S] TO MAKE SURE CLEAN AND SECURE. IF ENGINE HAS DISTRIBUTOR
WITH MULTIPLE WIRES RUNNING TO EACH SPARK PLUG, REMOVE DISTRIBUTOR CAP AND DRY ANY MOISTURE. MARK WIRES SO THEY GO BACK IN CORRECT LOCATIONS.

Buick Cars &... | Answered Yesterday


Sounds like what is called shutter changing to synthetic fluid fixed my 98 Lesabre

1997 Buick... | Answered Yesterday


Do you know that a replacement ECM would need programming ? Dealer .An it's a PCM - powertrain control module ,because transmission an engine modules are inside the same box (module) .Service of the PCM should normally consist of either replacement of the PCM or EEPROM programming. If the diagnostic procedures call for PCM replacement, inspect the PCM first to see if the PCM is the correct part. If the PCM is faulty, remove the PCM and install the new service PCM.
The new service PCM will not be programmed. You must program the new PCM. DTC P0602 indicates the EEPROM is not programmed or has malfunctioned.
There are no user serviceable parts in this PCM. The PCM should never be opened for any reason.
Important: When replacing the production PCM with a service PCM (controller), it is important to transfer the broadcast code and production PCM number to the service PCM label. Do not record this information on the PCM cover. Transfer allows positive identification of PCM parts throughout the service life of the vehicle.

Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
Remove the left sheet metal diagonal brace. Refer to Front End Sheet Metal Diagonal Brace Replacement - Left Side in Body Front End.
Remove the air cleaner assembly cover and lift the PCM from the assembly.
Disconnect the harness connectors from the PCM.
Remove the PCM from the engine compartment.

2005 Buick... | Answered Yesterday


Sounds like second gear went out, probably require rebuilding

Buick Cars &... | Answered Yesterday


when asking questions it really helps us and you if we have an idea given by you as to what you refer . many relays also lots of fuses what relay do you ask about

Buick Cars &... | Answered 2 days ago


Try this: (from net search ) http://www.autozone.com/repairguides/Repair-Pontiac-Mid-size-1974-1983-Repair-Guide/Engine-Mechanical/Timing-Chain/_/P-0900c152800849ff

Buick Cars &... | Answered 3 days ago


The service and repair manual with diagram will help you step by step to locate and fix the problem easily on your own and you will get the manual from the given link https://toolsnyou.com/

Buick Cars &... | Answered on Apr 19, 2019


Check oil level, 1993 cars have a lot o miles on them and engines wear our. The oil light comes on just before engine damage begins. Stop driving and check oil level. If you have add more tan 1 quart, your engine is losing oil, either by a leak or oil consumption cause by worn rings, piston or engine bore.
Good luck

1993 Buick Park... | Answered on Apr 17, 2019


Buy a haynesbook at parts or library sec629 has shopbooks

Buick Cars &... | Answered on Apr 17, 2019


Intake push rods and exhaust push rods are different lengths. You have them mixed up. I believe the exhaust are longer. You will know. If there is too much space, that is the short rod.

Buick Cars &... | Answered on Apr 17, 2019


Yeah ? so replace it .

Buick Cars &... | Answered on Apr 16, 2019


I think " Hoppe" makes a wiring kit that will plug right in, if you can't find that you may have to tap or splice into the wiring. Green-right turn/stop. Yellow-left turn/stop Brown- tail lights. White- ground. I hope this helps. Take care.

Buick Cars &... | Answered on Apr 16, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Popular Products

2000 Buick LeSabre
2000 Buick LeSabre

1,704 Questions

1997 Buick LeSabre
1997 Buick LeSabre

1,570 Questions

1995 Buick LeSabre
1995 Buick LeSabre

1,067 Questions

2002 Buick Rendezvous
2002 Buick Rendezvous

1,068 Questions

1994 Buick LeSabre
1994 Buick LeSabre

891 Questions

Top Buick Experts

Marvin
Marvin

Level 3 Expert

84540 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8850 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14640 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...