Boating - Page 3 - Popular Questions, Answers, Tips & Manuals
What year and iinfo on my Evinrude model #3302S serial #B13252
- Based on model number and serial number you provided, it appears that you have an Evinrude outboard motor that was manufactured in 1965. Here is some additional information about your motor:
- The model number, 3302S, indicates that it is a 3 horsepower (hp) motor with a short (S) shaft length.
- The serial number, B13252, is used to identify the specific motor and can be used to find additional information such as its exact manufacturing date and the original dealer it was sold to.
- This model of Evinrude motor is a two-stroke engine that runs on a gasoline/oil mixture. It has a single-cylinder powerhead and uses a manual recoil starter.
- The motor features a tiller handle for steering and throttle control, and has a built-in fuel tank with a capacity of about 1 quart. It can also be connected to an external fuel tank if desired.
- Since this motor is over 50 years old, it may require special maintenance and care to keep it running properly. You may want to consult with an experienced mechanic or Evinrude dealer for advice on how to maintain and repair the motor.
3/14/2023 6:12:42 AM •
Boating
•
44 views • 0 helpful votes
AOSmith 1hp lift motor starts then trips breaker , any ideas?, thants
There are a few possible reasons why your AOSmith 1hp lift motor starts and then trips the breaker:
- Overload: The motor may be overloaded and drawing too much current. Check the load on the motor and make sure it is within the motor's capacity.
- Short Circuit: A short circuit could be causing the motor to draw too much current and trip the breaker. Check the wiring for any signs of damage or wear.
- Faulty Motor: The motor itself could be faulty and causing the overload or short circuit. Check the motor windings for any signs of damage or wear.
- Tripped Thermal Overload: The motor may have a thermal overload switch that shuts off the motor if it gets too hot. Check the motor for any signs of overheating and reset the thermal overload switch if necessary.
- Faulty Breaker: The breaker itself could be faulty and tripping prematurely. Check the breaker for any signs of wear or damage.
It is recommended to consult a licensed electrician or motor technician to diagnose and fix the issue, as working with electricity can be dangerous if not done properly.
11/6/2022 11:04:41 AM •
Boating
•
76 views • 0 helpful votes
How to program frequency 8113.5 on my Furuno FSS1503 Single Sideband Radio Telephone?
To program a specific frequency on the Furuno FSS1503 Single Sideband Radio Telephone, you can follow these steps:
- Press the Power button to turn on the radio.
- Press the Frequency button to select the desired frequency range (HF, MF, or VHF).
- Use the arrow keys to select the desired frequency (8113.5 kHz in this case).
- Press the Enter button to confirm the frequency selection.
If the frequency is not working, there may be other factors affecting the radio's performance, such as interference, atmospheric conditions, or a faulty antenna. It is recommended to use an antenna coupler or tuner to optimize the radio's performance and ensure proper transmission and reception. If you are still experiencing issues, you may need to consult a professional technician or the manufacturer's customer support for further assistance.
I have a Minn Kota 315D 3 bank charger. When I plug it in to my electrical outlet only bank 1 shows a solid yellow light. I am not getting power to bank 2 and 3.
A solid yellow light on Bank 1 of your Minn Kota 315D 3 bank charger indicates that the charger is in "float" mode, which means it is maintaining the battery's charge at a safe level. It sounds like there may be an issue with the connections or wiring for Banks 2 and 3, preventing them from receiving power.
Here are a few things you can try:
- Check the connections between the charger and the batteries for Banks 2 and 3 to ensure they are tight and secure.
- Ensure that the circuit breaker for the charger is not tripped.
- Check the wiring for Banks 2 and 3 for any visible damage or corrosion.
- Ensure that the batteries for Banks 2 and 3 are not in a low state of charge or are not faulty.
- Try to reset the charger by unplugging it from the power source and plug it back in after a few minutes.
8/19/2022 11:49:02 AM •
Minn Kota...
•
136 views • 0 helpful votes
What should I look for in a structural engineer in Hull?
If you need to hire a structural engineering specialist, you first and foremost want someone with genuine experience. You should keep an eye out for companies that have a long-standing history within the region. For example, companies like
GGP Consult offer access to the kind of structural engineer Hull developers should be looking for.
Primarily, you should be focusing on finding someone who has designed something similar to what you are looking for. Look through their portfolio and ensure they have something in their professional history that matches up with what you will be building.
While most structural engineers can be quite versatile, it pays to know that your selected expert has built something that matches your ideas beforehand. Focus on these areas when hiring a Hull structural engineer.
9/23/2022 10:29:22 AM •
Boating
•
45 views • 1 helpful votes
Not finding what you are looking for?