Washing Machines - Answered Questions & Fixed Issues


Is the noise a thumping noice? How old is the washing machine? Did it just all of a sudden start making the noise? Have you tried running machine for a cycle empty? If so is the noise still there?
several explanations for noise,
I assume when you say agitating it is a top loading machine.
so 'hard time agitating' meaning the agitator is slow? Or skips?
try running machine with nothing in it and report back.

Gary

Washing Machines | Answered 3 hours ago | 14 views


washing machine ay?

Washing Machines | Answered 11 hours ago | 16 views


Hi,

What is the make and model of your washer?

Washing Machines | Answered 12 hours ago | 15 views


i have a chipper and it started giving lot of problems 4 yrs ago, so I got
this free Pdf manual from reliable-store for free and I don't think Ive visited a mechanic or fixya for help for more than 3-4 times out of the 20 times I fixed the chipper in these 4 years

Samsung Washing... | Answered 18 hours ago | 14 views


The plastic hose to the water level sensor switch can get suds or dirt stuff in it and causes issues like this. Take the hose loose and blow through it then run a couple plain hot water cycles to clean out access soap film and residues.

Samsung Washing... | Answered 23 hours ago | 17 views


My aw-sd160s todhiba washing machine was showing code E-21 ?? does spin?????

Washing Machines | Answered Yesterday | 167 views


You have to lift the top off. Take the screws out of the back. Lift the timer controls off. There should be a couple more screws under the timer compartment.

Kenmore Washing... | Answered Yesterday | 18 views


The pump and/or controller could be defective.

GE Washing... | Answered Yesterday | 18 views


Most common reason generically is there is a piece of cloth or lint or some form of foreign body somewhere or a bad seal and the machine has not received a Door Closed signal.

Check carefully, including any rubber seal or gasket, for breaks or warping, or foreign body.

Washing Machines | Answered Yesterday | 20 views


What brand and model #?

Washing Machines | Answered Yesterday | 20 views


If the lid is locking, the actuator is most likely the issue

Washing Machines | Answered Yesterday | 157 views


This has helped a lot of people with your Beko model https://www.youtube.com/watch?v=RFDur_lIzfg

Washing Machines | Answered Yesterday | 20 views


Most often this is due to the door not shutting properly.

Carefully examine to see if clothing or lint or foreign body is interfering with the full closure of the door.

The washer will not start if it does not receive a signal that the door is full closed.

Bosch Washing... | Answered Yesterday | 36 views


If you're in NY email moneysur@hotmail.com

Washing Machines | Answered Yesterday | 21 views


disconnect from electricity. take back panel off.you will see heater at bottom of tub held in by 1 10mm nut.disconnect wires to it. loosen this nut and pull heater out - you may have to help it with a screwdriver. you can then see into the gap between tub and drum and fish for the bra wire.
tell her not to wear bras with wires!!

Electrolux... | Answered Yesterday | 931 views


Might be a control board problem. Contact Malber USA at 1-800-600-8913. They will have replacement part and, if the machine is still under warranty, the part is free.

Malber WD1000... | Answered Yesterday | 440 views

Not finding what you are looking for?
Washing Machines Logo

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Marvin
Marvin

Level 3 Expert

83850 Answers

Brad Brown

Level 3 Expert

17827 Answers

paul
paul

Level 3 Expert

825 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...