Tools & Hardware - Others - Page 8 - Answered Questions & Fixed Issues

This can happen if you accidentally depress the spindle locking button while the tool is running -- a common problem since Dremel did not include any type of interlock to prevent it, and the button is right where you'd hold the tool for best control. If that happens, you probably will need to replace the tool or send it to Dremel for repair.

Depends on what you have, but if you need to shut off the engine to shift into the gears then you have a problem with the clutch assembly not releasing. Could be needing a new clutch disc or pressure plate or a simple adjustment on the clutch linkage or if it is hydraulic clutch bleed the system or replace the master and or slave cylinder.

I'm needing bearings for a model 2403016 6"belt & 9"Disc sander. NSK 257-6201v. 7/16 boar NSK 6202z. 6202N. 1/2 boar can you help me

I have a chop saw 15A 14-inch I need replace on/off trigger switch but I can't find it online to buy a new one somebody know where I can get a new part replacement for it or a spare one I can buy to fix it ?

clean the tool completely may fix it.

My stylus is doing exactly the same thing. l was advised by numerous people to change the capacitor in the charging dock, they also said that you can find youtube videos to guide you through it (the capacitor only cost a few cents when l bought it). I really should finish doing that job, although l did actually remove the 'screws'' from the base, l warn you- they are triangle and a nightmare to unscrew, see if you can find a triangle screwdriver BEFORE you start, or you'll end up doing what l did and destroying a perfectly good straight screwdriver!??. Good luck

Change tha capacitor 220uF and it will probably be fine! I did and now it is as new!

use B8 staples available at amazon, office max office depot, staples

Try fleabay or amuzun.

Hi, had the same problem. After market micro switch replacement for Hitachi NR 90GC from RS Components Stock number 682-1888 MPN; D2HWC203MR.Note; this requires soldering in with heatshrink and cutting flyleads to correct length. Part of the alignment issue can be the handle screws working loose over time with use. Don't force anything back when assembling and use a little grease on contact parts.

For parts this old, I start out looking on ebay by the part number and brand. If that falls through, I look for the whole product on ebay because there might be one cheap enough to strip a part from. Fact is, I don't find the part elsewhere on the web, even in part replacement sites. You might contact customer service at Kango or Milwaukee Tools but such is a long shot. Here is what ebay offers: kango 750 rotary hammer: Search Result ' eBay

you can but would need to chase down the needed overhaul parts or send in to a repair shop but give it a good cleaning and lube the bearings first

https://manuals.plus/bosch/pho-20-82-corded-compact-planer-manual#axzz7YG6vK5wp http://www.free-instruction-manuals.com/pdf/p3427802.pdf

Question edited for clarity to add Maker. Question moved to Make Model category. The lock button should lock the shaft. With the collet facing you, turn anti-clockwise with grips or pliers. They should never be done up _that_ tight. Try spraying with penetrating oil. Two version of the manual below.

DREMEL OF Multi 395

https://docs.rs-online.com > ... PDF the better products of its kind. • To get the optimum benefit from the tool we advise you to read this instruction manual thoroughly.

DREMEL Moto-Tool Owner's Manual

https://neurophysics.ucsd.edu > Manuals > Dremel PDF DREMEL. Moto-Tool Owner's Manual. Models 275, 285, 395, and 595. 3. HONESTLY NOW... Have you read this. OWNER'S MANUAL? This manual will tell you how to get ... 11 pages

Question moved from Cars and Trucks. Try Canadian Tire or Amazon. There was a recall on it. https://www.google.com/search?q=Mastercraft+batteries+54-3062-6+replacement+battery+charger ..

Question edited for clarity. Question moved from Cars and Trucks. Difficult without a Letter/Numerical Model Number, but this seems to indicated it has a left hand thread, which means it turns clockwise to undo. That was my first thought, so I looked for a manual. https://images-eu.ssl-images-amazon.com/images/I/B1X7J5EPy4S.pdf The search query should be 'make model manual'. https://www.google.com/search?q=ryobi+multi+tool+manual ..

It is a good job we are mind readers here at Fixya! Question edited FULL 'make model (what it is)' in all questions please. Question moved from Garden to Bosch Power Tools. https://www.google.com/search?q=Bosch+B4050+replacement+saw+blades ..

the grease is for the chuck as SDS chucks often seize up

It needs new blades - likely has a chip in one. See link for replacement tutorial